English
Notes:
•
Execute a Master Clear before you start learning (see the
method above).
•
Make sure both remote controls have full batteries before
you start learning codes.
•
Make sure you do not move the remote controls when
pressing the buttons.
•
You cannot learn any commands for the following buttons:
Learn, Setup, Source buttons TV, VCR, CBL, etc, M1, M2,
M3, ShowView, Xanura Home or directly under the SHIFT
button.
•
Experiment by learning two or three buttons first (to test
compatibility), before you learn all the buttons of your
original remote control.
•
When the memory is full, one of the Mode LED's will
flash for 3 seconds. You cannot learn any codes when the
memory is full. You can, however, erase a mode with
codes you stored. You can only erase a full mode.
•
By keeping the buttons for the existing remote control
pressed for a shorter period, there will be more memory
space left for learning codes on the XanuraHome remote
control. This also diminishes the chance that the remote
control learns the wrong codes.
•
Experiment with the distance between the remote
controls if you have problems learning the codes.
•
Some remote controls do not have the infrared LED in the
centre. Try experimenting by slightly moving the remote
controls (sideways or up/down).
•
Tube lighting and bright sunlight can affect the procedure.
•
Use the buttons L1, L2, L3 and L4 to learn the codes for
which the XanuraHome remote control does not have a
proper button. If you encounter any problems when
learning the codes of buttons, erase the memory and
start again.
•
You can only learn the codes for one original remote
control per mode, e.g. the codes for your DVD remote
control under the DVD button. With some combi devices
(e.g. a TV with built-in DVD player) you first have to learn
the TV functions in TV mode and then the DVD functions
in DVD mode. Learning the commands
1. Point your existing remote control at the XanuraHome
Remote (front to front). Keep a distance of 2,5 cm between
the remote controls.
2. Press the SETUP (8) button until one of the Mode LED's
stays lit. Release the SETUP (8) button.
3. Press the Mode button (TV, AUDIO, SAT, etc.) for the
device you want to learn. The LED will flash once.
4. Press the LEARN (24) button. The LED will flash once.
5. Press the button on the XanuraHome remote you want to
store the new command under. The LED will blink once.
6. Depending on the type of remote control you have, you
can use one of two methods:
a. Press the button on the existing remote control
you want to learn. Keep this button pressed until
the LED on the XanuraHome Remote
extinguishes. If the LED does not extinguish, but
starts flashing, you need to use method B. (If you
have just tried method A and want to try method B,
first repeat step 5).
b. Press the button on the existing remote control
you want to learn. Keep this button pressed as
28
MBO 1991494G01 001
long as you would when using the original remote
control.
7. Repeat steps 5 and 6 for every button you want to learn.
8. When you have finished learning the buttons, press
SETUP (8)
Erasing the commands learned per mode to clear
memory space
You can erase the commands learned and saved for each
separate function (TV, VCR, etc.):
1. Keep the SETUP (8) button pressed until one of the Mode
LED's stays lit. Release the SETUP (8) button.
2. Press the Mode button of your choice (TV, VCR, etc.).
The LED will flash once.
3. Press the LEARN (24) button twice.
4. Press SETUP (8). The LED will extinguish after a few
seconds.
5. All commands learned and saved for the selected function
have now been erased.
4.7 Identifying codes found
If the batteries are taken out of the remote for a longer
period, the programmed codes can be erased from the
memory. Therefore it is wise to write down the codes, so
you will be able to reprogram the remote control quickly If
you don't know the code (for example because you found the
code by autosearch) you can identify it as described below:
1. Press and hold
SETUP
(8) until the LED indicator (2)
lights steadily. Release
SETUP
.
2. Press the mode key (3) for the equipment you want to
identify (VCR, CBL, DVD, CD, ASAT, DSAT or AUX). The
LED blinks once.
3. Press again SETUP. The LED blinks once.
4. To identify the first digit press each number button from
0 - 9
(9) until the LED blinks. The number you pressed is the
first digit of the code.
5. Press each number key from
0 - 9
as above to find the
second digit.
6. Press each number key from
0 - 9
as above to find the
third digit. When the third digit has been found the LED will
go off.
29
MBO 1991494G01 001
