background image

4

3. UAV System

Warning:

Do not get close to the propeller or motor when they are working.

The product is not suitable for people under 18.

UAV management regulations and local airspace control regulations carefully before

use. Once you use this product, you will be deemed to have read the relevant

regulations and documents. EAVision will not be responsible for any legal liability

arising from the use of this product in violation of the laws and regulations.

While using the UAV, please ensure that the power supply system works well and

arms of UAV are in the right position. Keep the UAV away from crowd and dangerous

articles.

It is strictly prohibited for operators to operate the UAV after drinking, drug taking

or drug anesthesia, or when the operator is in dizziness, fatigue or other poor physical

and mental conditions. New operator without enough flight training shall not operate

the UAV independently outside the training site.

Don't operate the UAV in bad weather such as rainy days, snowy days or windy

days (wind speed 19mph or above)

Do not operate the UAV in magnetic field interference area and radio interference

area (such as high-voltage tower, large-scale power equipment, radio and television

transmission tower and mobile phone base station, etc). If it is really necessary, please

ensure that there are no other people within 200m of the operation area.

This statement is very important for the safe use of the product and your

legitimate rights and interests. Suzhou Eavision Robotic Technologies Co., Ltd reserves

the right to update this disclaimer. Thank you again for choosing our product.

Summary of Contents for EA2021E




































































Reviews: