background image

6

MAINTENANCE AND SERVICE

6.1

Service

There are no user serviceable parts inside either the MX8700 or MX8750 processors.  In case of failure,
refer all servicing to the factory. Service and repair information may be obtained by contacting the EAW
Service Department or the EAW distributor for your country.

WARNING: 

Do not remove the product covers or panels.  Do not operate the product without the

covers and panels properly installed.

6.2

How To Contact EAW

We have tried to answer most questions you may have about the MX8700 and MX8750 in this manual.
Should you need further assistance, please do not hesitate to contact us.  You can contact us in several
different ways:

Main

Eastern Acoustics Works

Tel

800-992-5013 (USA only)

One Main Street

Tel

508-234-6158

Whitinsville, MAs  01588 USA

Fax

508-234-8251

Service

Eastern Acoustic Works

Tel  

800-992-6001 (USA only)

EAW Service Department

Tel   

508-234-6001

One Main Street

Fax  

508-234-3776

Whitinsville, MA 01588  USA

e-mail  serviced@eaw.com

Literature and Specifications

Eastern Acoustic Works

Tel   

800-992-5013 (USA only)

EAW Literature Department

Tel   

508-234-6158

One Main Street

Fax  

508-234-8251

Whitinsville, MA 01588 USA

e-mail  info@eaw.com

Web Site

http://www.eaw.com/

Page 9

Summary of Contents for MX8700













Reviews: