background image

2

 – VRS12 and VRS18

VRS12 and VRS18 – 

3

14.  Rigging Precautions: When mounting or suspending EAW Commercial loudspeaker 

enclosures, it is essential that load ratings, rigging techniques, and special safety 

considerations be appropriate for the installation. Use only the mounting/rigging points 

on the loudspeaker enclosure intended for this purpose. The user must determine the load 

requirements, dynamic loading, and any other contributing factors affecting the loudspeaker 

installation. The user must determine the proper design factor for specific applications and 

the required load rating of the connection to structure. Comply with all applicable federal, 

state, and local regulations.

       EAW Commercial strongly recommends the following rigging system practices:

•  Documentation: Thoroughly document the mounting/rigging design with detailed 

drawings and parts lists.

•  Analysis: Have a licensed structural engineer or other qualified professional review and 

approve the mounting/rigging design before its implementation.

•  Installation: Use personnel experienced and qualified for mounting/rigging loudspeakers 

in accordance with and in compliance with all federal, state and local regulations.

DANGER: Loudspeakers should be mounted or suspended only by persons with knowledge 

of the proper hardware and rigging techniques. When stacking or pole-mounting 

loudspeakers, be sure that they are stabilized and secured from falling over or being 

accidentally pushed over. Failure to follow these precautions may result in damage to the 

equipment, personal injury, or death.

TABLE OF CONTENTS

1. SAFETY INSTRUCTIONS........................................................ 2

2. INTRODUCTION....................................................................... 4

3. INSTALLATION ........................................................................ 5

4. CONNECTIONS........................................................................ 6

5. OPERATION.............................................................................. 8

6. SPECIFICATIONS..................................................................... 9

    Dimensions.............................................................................. 10

    Performance Graphs .............................................................. 11

7. TROUBLESHOOTING .............................................................. 12

8. SERVICE and MAINTENANCE............................................... 13

9. WARRANTY ............................................................................. 15

Summary of Contents for VRS12 VRS18

















Reviews: