Deutsch: Seite 1
English: Page 2
Français: Page 3
Italiano: Pagina 4
Español: Pagina 5
Sollte dies an Ihrer PlayStation 2 nicht funktionieren, versuchen Sie bitte noch folgendes:
Schließen Sie unser Kabel ganz normal an Ihre Konsole an und
stellen Sie sicher, dass sich
keine CD/DVD im Laufwerk und keine Memory Cards in der Konsole befinden
. Schalten Sie
nun die Konsole ein und warten Sie 15 Sekunden – auch wenn Sie dabei kein Bild sehen.
Betätigen Sie anschließend die folgenden Tasten
– warten Sie dabei 2 Sekunden zwischen den
Eingaben:
1.
Drücken Sie 1x runter (▼) auf dem D-Pad
2.
Drücken Sie X
3.
Drücken Sie 3x runter (▼ ▼ ▼) auf dem D-Pad
4.
Drücken Sie X
5.
Drücken Sie links (◄) auf dem D-Pad
6.
Drücken Sie X
7.
Drücken Sie die Kreis-Taste (
O
)
Nun sollten Sie wieder ein Bild sehen können.
Bei weiteren Fragen und Problemen, können Sie sich gerne an unseren Kundenservice
unter
support@trade4less.de
/ Tel: 07121-386967 wenden.
PlayStation 3
:
Stellen Sie sicher, dass die Konsole ausgeschaltet ist und halten Sie dann den
Einschaltknopf für 5 Sekunden gedrückt bis ein Signalton erklingt.
Die Konsole erkennt das
Kabel nun automatisch.
PlayStation 2
:
Stecken Sie den grünen Stecker des Kabels in den gelben Anschluss Ihres
Fernseher und wechseln Sie auf das Eingangssignal
„Composite“/“Video“
. So sollten Sie ein
schwarz-weiß Bild erhalten.
Starten Sie die Konsole nun ohne Spiel und öffnen Sie die Einstellungen um dort das Signal auf
„Component/YUV“
umstellen. Verbinden Sie das Kabel anschließend korrekt mit Ihrem
Fernseher und wechseln Sie auch dort auf den Eingang
„Component“/“YUV“
um ein
kristallklares Bild zu erhalten.
Sollten Sie nach Anschluss des Kabels kein Bild sehen, dann gehen Sie bitte
folgendermaßen vor:
Eaxus® YUV Component Kabel für PlayStation 3 & 2
Installationshinweise
!
If this does not work on your PlayStation 2, please try the following:
Connect our cable to your console normally and
make sure there is no CD/DVD in the drive and
no memory cards in the console
. Now turn on the console and wait 15 seconds - even if you
don‘t see a picture.
Now press the following keys
- always wait 2 seconds
between entries:
1.
press down (▼) on the D-Pad
2.
press X
3.
press down 3 times (▼ ▼ ▼) on the D-Pad.
4.
press X
5.
press left (◄) on the D-Pad.
6.
press X
7.
press the circle button (
O
)
Now you should be able to see a picture again.
If you have any further questions or problems, please feel free to contact our customer
service at
support@trade4less.de
.
PlayStation 3:
Make sure the console is turned off, then press and hold the power button
for 5 seconds until you hear a beep.
The console will now automatically detect the cable.
PlayStation 2
:
Plug the green connector of the cable into the yellow connector of your TV and
switch to the input signal
„Composite“/“Video“
. This should give you a black and white picture.
Now start the console without a game and open the settings to change the signal to
„Component/YUV“
. Connect the cable correctly to your TV and change the input to
„Component“/“YUV“
to get a crystal clear picture.
If you do not see a picture after connecting the cable, proceed as follows:
Eaxus® YUV Component Cable for PlayStation 3 & 2
Installation instructions
!
Deutsch: Seite 1
English: Page 2
Français: Page 3
Italiano: Pagina 4
Español: Pagina 5