background image

6

SAFETY TIPS

• 

Read the entire manual before attempting to pilot your helicopter. 

• 

This product is intended for indoor use, and works best indoors. We do 
not recommend using the product outdoors.

• 

Never attempt to fl y your helicopter in a cluttered space. This helicopter 
was intended for obstacle free wide area spaces.

• 

Make sure all people and animals are 3-5 feet from the helicopter before 
you start fl ying it. 

• 

Always keep focus on your helicopter, and do not attempt to fl y/land/or 
crash anywhere on or near any other people or animals. 

• 

The rotating parts on the helicopter could lead to injury.  Never put any 
body part including the hands and face, close to the rotating parts. Only 
operate this product standing, as it allows for quick movement away from 
the helicopter if necessary. 

• 

Never operate the helicopter using parts that are altered in shape or  
damaged in any form. 

TROUBLESHOOTING

Problem

Cause

Correction

Helicopter is 
not responding 
to remote

Incorrect channel 
selection on the 
remote 

Gently press forward on the left 
joystick and switch between all 3 
channels until the helicopter takes 
fl ight. This is the correct channel.

Loss of Control

Interference of 
another remote 
controlled  device            

Interference by 
other conditions 
such as lighting

Avoid all other remote controlled 
devices running on the same 
channel.                       

Change environment to better 
suited conditions.

Helicopter 
Spinning out of 
control

Incorrect trim 
adjustment

Adjust the trim as shown above 
to fi nd the proper adjustment.

XC9977IS01EXC.indd   6

XC9977IS01EXC.indd   6

8/24/11   2:43 PM

8/24/11   2:43 PM

Summary of Contents for Phantom Eagle XC9977









Reviews: