Operating instructions
K1G200-AD37-02
Translation of the original operating instructions
3.2 Nominal data
Motor
M1G074-BF
Nominal voltage / VDC
48
Nominal voltage
range / VDC
36 .. 57
Method of obtaining
data
fa
Status
prelim.
Speed (rpm) / min
-1
4140
Power consumption / W
183
Current draw / A
5.6
Max. back pressure / Pa
520
Min. ambient
temperature / °C
-25
Max. ambient
temperature / °C
70
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
Actual
Req. 2015
01 Overall efficiency η
es
/ %
44.6
32.4
02 Measurement category
A
03 Efficiency category
Static
04 Efficiency grade N
62.2
50
05 Variable speed drive
Yes
06 Year of manufacture
The year of manufacture is specified on the
product's rating label.
07 Manufacturer
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart ·
HRA 590344
D-74673 Mulfingen
08 Type
K1G200-AD37-02
09 Power consumption P
e
/ kW
0.21
09 Air flow q
v
/ m³/h
700
09 Pressure increase total p
sf
/
Pa
430
10 Speed (rpm) n / min
-1
4070
11 Specific ratio
*
1.00
12 Recycling/disposal
Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance
Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
3.4 Technical description
Weight
1.66 kg
Size
200 mm
Motor size
74
Rotor surface
Painted black
Impeller material
PA6 plastic, glass-fiber reinforced
Housing material
PA6 plastic, glass-fiber reinforced
Support bracket
material
PA6 plastic, glass-fiber reinforced
Number of blades
7
Direction of rotation
Clockwise, viewed toward rotor
Degree of protection
IP20; installation- and position-dependent
Insulation class
"B"
Moisture (F) /
Environmental (H)
protection class
H0 - dry environment
Installation position
Any
Cooling hole/opening
On rotor side
Mode
S1
Motor bearing
Ball bearing
Technical features
- Tach output
- Motor current limitation
- Soft start
- Control input 0-10 VDC / PWM
Motor protection
Reverse polarity and locked-rotor
protection
with cable
Lateral
Conformity with
standards
EN 60950-1
Approval
UL 1004-1; EAC; CSA C22.2 No. 77
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.5 Mounting data
Strength class of
screws
8.8
For screw clearance, see Chapter 3.1 Product drawing
;
Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Item no. 50899-5-9970 · ENU · Change 212353 · Approved 2020-05-20 · Page 5 / 10
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
