ebm-papst K3G450-PA21-C1 Operating Instructions Manual Download

Page: 4 / 14

Operating instructions

K3G450-PA21-C1

Translation of the original operating instructions

3. TECHNICAL DATA

3.1 Product drawing

All dimensions in mm.

Installation position: Shaft horizontal (only install support struts vertically as illustrated) or rotor on bottom; rotor on top on request

Cable diameter min. 4 mm, max. 10 mm, tightening torque 4 ± 0.6 Nm

Cable diameter min. 9 mm, max. 16 mm, tightening torque 6 ± 0.9 Nm

Tightening torque 3.5±0.5 Nm

Inlet ring with pressure tap (k-factor: 240)

Mounting holes for FlowGrid

Item no. 55935-5-9970 · ENU · Change 209539 · Approved 2021-02-12 · Page 4 / 14

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com

Summary of Contents for K3G450-PA21-C1















Search results

Summary of Contents for K3G450-PA21-C1

Reviews:

Related manuals for K3G450-PA21-C1

Brands by name

Popular brands

ebm-papst K3G450-PA21-C1, Operating Instructions Manual

Search results

Summary of Contents for K3G450-PA21-C1

Reviews:

Related manuals for K3G450-PA21-C1

Brands by name

Popular brands