ebm-papst M3G112-GA53-72 Operating Instructions Manual Download

Page: 4 / 12

Operating instructions

M3G112-GA53-72

Translation of the original operating instructions

3. TECHNICAL DATA

3.1 Product drawing

All dimensions in mm.

Direction of rotation counterclockwise, viewed toward shaft

Through-hole for M10 screw

Max. clearance for screw 12 mm

Max. clearance for screw 16 mm

Cable diameter min. 4 mm, max. 10 mm, tightening torque 2±0.3 Nm

Tightening torque 3.5±0.5 Nm

Groove depth 3.5 mm

Key DIN 6885 - A - 6 x 6 x 32

Max. permissible axial load: 200 N

Max. permissible radial load: 1200 N

Item no. 50876-5-9970 · ENU · Change 94899 · Approved 2018-03-02 · Page 4 / 12

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com

Summary of Contents for M3G112-GA53-72













Search results

Summary of Contents for M3G112-GA53-72

Reviews:

Related manuals for M3G112-GA53-72

Brands by name

Popular brands

ebm-papst M3G112-GA53-72, Operating Instructions Manual

Search results

Summary of Contents for M3G112-GA53-72

Reviews:

Related manuals for M3G112-GA53-72

Brands by name

Popular brands