ebm-papst R3G900-AQ01-01 Operating Instructions Manual Download

Page: 8 / 12

Operating instructions

R3G900-AQ01-01

Translation of the original operating instructions

Fig. 3: Cable routing for fans installed upright.

4.4 Factory settings

Factory settings with which the device is pre-set by ebm-papst.

Control mode
parameter set 1

PWM controlling

Control mode
parameter set 2

PWM controlling

Fan / device adress

Max. PWM / %

100

Min. PWM / %

Save set value to
EEPROM

Yes

Set value control

Analogue (linear)

Control function
parameter set 1

Positive (heating)

Control function
parameter set 2

Positive (heating)

Item no. 51307-5-9970 · ENG · Revision 82539 · Release 2014-05-08 · Page 8 / 12

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com

Summary of Contents for R3G900-AQ01-01













Search results

Summary of Contents for R3G900-AQ01-01

Reviews:

Related manuals for R3G900-AQ01-01

Brands by name

Popular brands

ebm-papst R3G900-AQ01-01, Operating Instructions Manual

Search results

Summary of Contents for R3G900-AQ01-01

Reviews:

Related manuals for R3G900-AQ01-01

Brands by name

Popular brands