Operating instructions
W8D630-KN01-01
Translation of the original operating instructions
3.2 Nominal data
Motor
M8D110-GF
Phase
3~
3~
3~
Nominal voltage / VAC
400
400
480
Wiring
Δ
Δ
Δ
Frequency / Hz
50
60
60
Method of obtaining
data
ml
ml
ml
Valid for approval/
standard
CE
CE
CE
Speed (rpm) / min
-1
670
730
780
Power consumption / W
305
390
460
Current draw / A
0.85
0.85
0.9
Max. back pressure / Pa
70
80
90
Min. ambient
temperature / °C
-40
-40
-40
Max. ambient
temperature / °C
20
20
20
Max. safe operating
speed (rpm) /
min
-1
1250
@ 60 °C
1250
@ 60 °C
1250
@ 60 °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Data according to Commission Regulation (EU) 327/
2011
Actual
Req. 2015
01 Overall efficiency η
es
/ %
31.9
30.4
02 Measurement category
A
03 Efficiency category
Static
04 Efficiency grade N
41.5
40
05 Variable speed drive
No
06 Year of manufacture
The year of manufacture is specified on the
product's rating label.
07 Manufacturer
ebm-papst Mulfingen GmbH & Co. KG
Amtsgericht (court of registration) Stuttgart
· HRA 590344
D-74673 Mulfingen
08 Type
W8D630-KN01-01
09 Power consumption P
e
/ kW
0.3
09 Air flow q
v
/ m³/h
5015
09 Pressure increase total p
sf
/
Pa
70
10 Speed (rpm) n / min
-1
670
11 Specific ratio
*
1.00
12 Recycling/disposal
Information on recycling and disposal is
provided in the operating instructions.
13 Maintenance
Information on installation, operation and
maintenance is provided in the operating
instructions.
14 Additional components
Components used to calculate the energy
efficiency that are not apparent from the
measurement category are detailed in the
CE declaration.
*
Specific ratio = 1 + p
fs
/ 100 000 Pa
Data obtained at optimum efficiency level. The ErP data is determined using a motor-impeller
combination in a standardized measurement setup.
3.4 Technical description
Weight
18.84 kg
Size
630 mm
Motor size
110
Rotor surface
Painted black
Terminal box material
PP plastic
Blade material
Press-fitted sheet steel blank, sprayed
with PP plastic
Fan housing material
PP plastic
Material guide vanes
PP plastic
Guard grille material
Steel, coated with black plastic (RAL
9005)
Number of blades
5
Airflow direction
V
Direction of rotation
Counterclockwise, viewed toward rotor
Degree of protection
IP54
Insulation class
"F"
Moisture (F) /
Environmental (H)
protection class
H2
Ambient temperature
note
If there is a risk of ice formation, the fan
is only to be operated with a heating tape
in the fan housing. For more detailed
information, consult ebm-papst. As a fan
for use with industrial evaporators,
suitable for ambient temperatures
between -40°C and +20°C, occasional
start-up at up to +40°C permissible.
Installation position
See fitting instructions
Condensation
drainage holes
On rotor side
Mode
S1
Motor bearing
Ball bearing with low-temperature lubricant
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
<= 3.5 mA
Motor protection
Thermal overload protector (TOP) with
basic insulation
Protection class
I (with customer connection of protective
earth)
Conformity with
standards
EN 61800-5-1; EN 60034-1; CE
Approval
VDE; EAC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
;
Use the device in accordance with its degree of protection.
Item no. 15829-5-9970 · ENU · Change 99214 · Approved 2018-05-15 · Page 6 / 13
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
