background image

Chengdu Ebyte Electronic Technology Co.,Ltd.                                                                                  E62-DTU (433D20) user manual 

Copyright ©2012–2019

Chengdu Ebyte Electronic Technology Co,;Ltd                                                                                                                               12

 

 
 

7.2.

 

Parameter setting  instruction 

 

 

Parameter 

Description   

Baud rate 

The serial port baud rate of a wireless data station at work

1200bps

115200bps

 

Odd-even check 

Support 8N1:no check 

8E1:even-check

8O1:odd-check

Both are 8-bit data bits and 1-bit stop 

bits. 

Air data rate

bps

 

Wireless communication  rate, also known as air baud rate air rate high,  data transmission speed, 

transmission of the same data time delay is small, but the transmission distance will become 

shorter.

 

64kbps is the most recommended  value 

Transmitting power 

In order to ensure the working efficiency, it is recommended  to use the maximum  power. If the 

transmitted power is reduced, the communication distance will become  shorter and the required 

current will be reduced 

FEC 

The lost or interfered data can be partially corrected by complex  encoding,  which can improve 

the equivalent receiving  sensitivity by about 3dBm. Turning off this function can reduce the 

communication  delay. 

Transmission mode 

Transparent transmission, and send-as-received  fixed  points, broadcasting is not supported 

Wake Up Time 

There is no direct relationship with the communication  delay. If the customer needs low-power 

applications, this option shall be adjusted as required to ensure t he communication  stability. 

This parameter is self-adaptive and needs no attention from the user. 

IO driven 

By default, select the internal TTL signal  drive mode

 

Station Address 

Internal address of wireless data station, stations with the same address as those independent of 

M odbus address can communicate  with each other. This feature can be used to realize software 

filtering  grouping input range :0~65535, decimal  number.

 

 

Frequency Channel   

It is equivalent to the working frequency of wireless data transmission station. Each channel 

corresponds to its different working frequency. Theoretically, different frequency channels 

cannot communicate  with each other. 

 

Summary of Contents for 433D20


















Reviews: