background image

Chengdu Ebyte Electronic Technology Co., Ltd.                                                                                                                                  E01-2G4M27D User Manual 

 

Copyright ©2012–2018

Chengdu Ebyte Electronic Technology Co.,Ltd.

                                                                                                                                        

 

2. Specification and parameter 

2.1 Limit parameter 

Main  parameter 

Performance 

Remark 

Min. 

Max. 

Power supply

V

 

5.5 

Voltage  over 5.5V will cause permanent damage  to module 

Blocking  power

dBm

 

10 

Chances of burn is slim when modules are used in short distance 

Operating temperature

 

-40 

85 

2.2 Operating Parameter   

Main  parameter 

Performance 

Remark 

Min. 

Typ. 

Max. 

Operating voltage

V

 

2.5 

3.3 

5.5 

≥3.3V ensures output power 

Communication level

V

 

3.3 

For 5V TTL, it may be at risk of 

burning down 

Operating temperature

 

-40 

85 

Industrial design 

Operating frequency

GHz

 

2.4 

2.525 

Support ISM band 

Power 

consumption 

TX current@3.3V

mA

 

490 

Instant power consumption 

TX current@5.0V

mA

 

390 

Instant power consumption 

RX current

mA

 

22 

Sleep current 

μA

 

N/A 

Max Tx power

dBm

 

26.8 

27 

27.3 

Receiving  sensitivity

dBm

 

-98.5 

-99 

-99.5 

Air data rate is 250kbps 

Air data rate

bps

 

250k 

2M  

Controlled via user’s programming 

For ultra-low  power users, the power supply can be directly turned off externally.

 

 

Main  parameter 

Description 

Remark 

Distance for reference 

2500m 

Test condition

clear and open area, antenna gain:  5dBi

antenna height: 2.5m

air data rate: 250kbps 

FIFO 

32Byte 

M ax length transmitted each time 

Crystal frequency  

16M Hz 

M odulation 

GFSK 

Package 

DIP 

Connector 

2.54mm Pin 

Communication interface 

SPI 

0-10M bps 

Size 

18 * 33.4mm 

Without SM A 

Antenna 

SM A-K 

50ohm impedance 

Summary of Contents for E01-2G4M27D












Reviews: