background image

Chengdu Ebyte Electronic Technology Co., Ltd.

E22-400T30S1C User manual

Copyright ©2012–2018,Chengdu Ebyte Electronic Technology Co.,Ltd.

6

Forward error correction

: The module has FEC forward error correction algorithm, which has high coding efficiency and

strong error correction capability. In the case of sudden interference, it can actively correct the interfered data packets,
greatly improving reliability and transmission distance. When without FEC, such packets can only be discarded.

Deep sleep function

: When the module is in sleep mode, mode 3, the wireless receiver is turned off and the

micro-controller is in a sleep state; at this time, the power consumption of the whole device is about 2uA.

Watchdog

: The module has a built-in watchdog and performs precise time layout. Once an exception occurs, the

module will restart within 1 second and continue to work according to the previous parameter settings.

Parameter saving

: After the user sets the parameters, the module parameters will be saved, the power will not be lost,

and the module will work according to the set parameters after power-on.

Applicable environment

: 433MHz is free frequency band, users can use it directly without application; 433MHz features

certain penetration and diffraction ability, suitable for environment with small data volume, long transmission distance
and easy to be interfered.

2. Specification and parameter

2.1 Limit parameter

Main parameter

Performance

Remark

Min.

Max.

Power supply(V)

0

5.5

Voltage over 5.5V will cause permanent

damage to module

Blocking power(dBm)

-

10

Chances of burn is slim when modules

are used in short distance

Operating temperature(℃)

-40

85

/

2.2 Operating parameter

Main parameter

Performance

Remark

Min.

Typ.

Max.

Operating voltage(V)

2.3

5.0

5.5

≥5.0 V ensures output power

Communication level(V)

3.3

For 5V TTL, It is recommended to add

level conversion

Operating temperature(℃)

-40

-

85

Industrial design

Operating frequency(MHz)

410.125

-

493.125

Support ISM band

Power
consump
tion

TX current(mA)

610

Instant power consumption

RX current(mA)

17

Sleep current (μA)

2

Software is shut down

Max Tx power(dBm)

29.5

30.0

30.5

Receiving sensitivity(dBm)

-147

-148

-149

Air data rate is 2.4kbps

Air data rate(bps)

0.3k

2.4k

62.5k

Controlled via user’s programming

Summary of Contents for E22-400T30S1C




























Reviews: