Ebyte E22-900T30D User Manual Download

Page: 15 / 25

Chengdu Ebyte Electronic Technology Co., Ltd.

E22-900T30D User Manual

Returen: C1

E.g 2: Configure module address (0x1234), network address (0x00), serial port (9600 8N1) and air data rate

(1.2K).

Send: C0 00 04 12 34 00 61

Return: C1 00 04 12 34 00 61

Read register

Command: C1+starting parameters

Response: C1+starting parameters

E.g 1

：

Read channel

command starting address length parameter

Send:

Returen: C1

E.g 2: Read module address, network address, serial port and air data rate.

Send: C1 00 04

Return: C1 00 04 12 34 00 61

Set

temporary

registers

Command: C2+starting parameters

Response: C1+starting parameters

E.g 1: Channel is 0x09

command starting address length parameter

Send:

Returen: C1

E.g 2: Configure module address (0x1234), network address (0x00), serial port (9600 8N1) and air data rate

(1.2K).

Send: C2 00 04 12 34 00 61

Return: C1 00 04 12 34 00 61

Wireless

configuration

Command: CF CF + normal command

Respond

：

CF CF + normal respond

E.g 1: Channel is 0x09

Command head command starting address length parameter

Send:

CF CF

Returen: CF CF

E.g 2: Configure module address (0x1234), network address (0x00), serial port (9600 8N1) and air data rate

(1.2K).

Send: CF CF C2 00 04 12 34 00 61

Return: CF CF C1 00 04 12 34 00 61

Wrong format

Wrong format respond: FF FF FF

7.2 Register description

Address

Read or

write

Name

Description

Remark

00H

Read/Wr

ite

ADDH

（

default 0

）



The module address is high byte and low byte. Note:

When the module address is FFFF, it can be used as

the broadcast and monitor address, that is the module

will not perform address filtering.

01H

Read/Wr

ite

ADDL

（

default 0

）

02H

Read/Wr

ite

NETID

（

default 0

）



Network address, used to distinguish the network.

When communicating with each other, they should

be set to the same.

Summary of Contents for E22-900T30D

























Search results

Summary of Contents for E22-900T30D

Reviews:

Related manuals for E22-900T30D

Brands by name

Popular brands

Ebyte E22-900T30D, User Manual

Search results

Summary of Contents for E22-900T30D

Reviews:

Related manuals for E22-900T30D

Brands by name

Popular brands