background image

Chengdu Ebyte Electronic Technology Co., Ltd.

E220-900T30D User Manual

Copyright ©2012–2020, Chengdu Ebyte Electronic Technology Co.,Ltd.

3

Disclaimer and copyright notice

The information in this article, including the URL for reference, is subject to change

without notice. The document is provided "as is" without warranty of any kind, including
any warranty of merchantability, fitness for a particular purpose or non-infringement, and
any warranty of any proposal, specification or sample referred to elsewhere. This document
does not bear any liability, including any infringement of any patent rights resulting from
the use of the information contained in this document. No estoppel or other license, express
or implied, is granted herein for the use of intellectual property.

All the test data obtained in this paper are obtained by E-Baite laboratory, and the actual

results may be slightly different.

It is hereby declared that all trade names, trade marks and registered trade marks

mentioned herein are the property of their respective owners.

The right of final interpretation belongs to Chengdu Yibaite Electronic Technology Co.,

LTD.

The attention

The contents of this manual may change due to product version upgrade or other reasons. E-baite
Electronic Technology Co., Ltd. reserves the right to modify the contents of this manual
without any notice or prompt. This manual is only used as a guide, and Chengdu Yibaite
Electronic Technology Co., Ltd. makes every effort to provide accurate information in this
manual, but Chengdu Yibaite Electronic Technology Co., Ltd. does not guarantee that the
content of this manual is completely free of errors, and all statements, information and
Suggestions in this manual do not constitute any express or implied warranty.

Summary of Contents for E220-400T30D























Reviews: