background image

Chengdu Ebyte Electronic Technology Co., Ltd.

E220-900T30D User Manual

Copyright ©2012–2020, Chengdu Ebyte Electronic Technology Co.,Ltd.

4

1. Overview

1.1 Introduction

E220-900T30D adopts a new generation of LoRa spread spectrum technology

and a wireless serial port module (UART) designed based on the LLCC68 chip

scheme. It has a variety of transmission methods, works in the (850.125

930.125MHz) frequency band (default 868.125MHz), TTL level output, compatible

with 3.3V and 5V IO port voltage.

E220-900T30D adopts a new generation of LoRa spread spectrum technology,

supports air wake-up, carrier monitoring, communication key and other functions,

supports sub-package length setting, and Ebyte provides customized development

services.

1.2 Features

The new LoRa spread spectrum modulation technology developed based on LLCC68, it brings a longer communication distance
and stronger anti-interference ability;

Support users to set the communication key by themselves, and it cannot be read, which greatly improves the confidentiality of
user data;

Support LBT function, monitor the channel environment noise before sending, which greatly improves the communication
success rate of the module in harsh environments;

Support RSSI signal strength indicator function for evaluating signal quality, improving communication network, and ranging;

Support air wakeup, that is, ultra-low power consumption function, suitable for battery-powered applications;

Support fixed-point transmission, broadcast transmission, channel monitoring;

Support deep sleep, the power consumption of the whole machine is about 5uA in this mode;

The module has built-in PA+LNA, and the communication distance can reach 10km under ideal conditions;

The parameters are saved after power-off, and the module will work according to the set parameters after power-on;

Efficient watchdog design, once an exception occurs, the module will automatically restart and continue to work according to the
previous parameter settings;

Support the data transmission rate of 2.4k

62.5kbps;

Support 3.0

5.5V power supply, power supply greater than 5V can guarantee the best performance;

Industrial standard design, supporting long-term use at -40

+85

;

SMA antenna interface.

1.3 Application

Home security alarm and remote keyless entry;

Smart home and industrial sensors;

Wireless alarm security system;

Building automation solutions;

Wireless industrial-grade remote control;

Advanced Meter Reading Architecture (AMI);

Automotive industry applications.

Summary of Contents for E220-900T30D























Reviews: