background image

Chengdu Ebyte Electronic Technology Co,;Ltd

E30-490T20D user manual

Copyright ©2012–2019

Chengdu Ebyte Electronic Technology Co,;Ltd

17

The ground will absorb and reflect wireless radio wave, so the performance will be poor when testing near ground.

Sea water has great ability in absorbing wireless radio wave, so performance will be poor when testing near the sea.

The signal will be affected when the antenna is near metal object or put in a metal case.

Power register was set incorrectly, air data rate is set as too high (the higher the air data rate, the shorter the
distance).

The power supply low voltage under room temperature is lower than 2.5V, the lower the voltage, the lower the
transmitting power.

Due to antenna quality or poor matching between antenna and module.

9.2 Module is easy to damage

Please check the power supply source, ensure it is 2.0V~3.6V, voltage higher than 3.6V will damage the module.

Please check the stability of power source, the voltage cannot fluctuate too much.

Please make sure antistatic measure are taken when installing and using, high frequency devices have electrostatic
susceptibility.

Please ensure the humidity is within limited range, some parts are sensitive to humidity.

Please avoid using modules under too high or too low temperature.

9.3 BER(Bit Error Rate) is high

There is co-channel signal interference nearby, please be away from interference sources or modify frequency and
channel to avoid interference;

Poor power supply may cause messy code. Make sure that the power supply is reliable.

The extension line and feeder quality are poor or too long, so the bit error rate is high;

10 Production guidance

This type is full-sized module, when the welder welds the module, he must be welding according to the anti-static

regulation. This product is allergic to static, randomly welding the module will have the chance of damaging it
permanently.

11.E30 series

Model No.

Core IC

Frequency

Hz

Tx

power

dBm

Distance

km

Air Data

Rate

Package

Size
mm

Interface

E30-433T20S3

SI4438

433M

20

2.5

1k~25k

SMD

16 * 26

IPEX/External

E30-780T20S

SI4463

780M

20

2.5

1k~25k

SMD

17 * 30

IPEX/External/Spring

E30-868T20D

SI4463

868M

20

2.5

1k~25k

DIP

21 * 36

SMA-K

E30-868T20S

SI4463

868M

20

2.5

1k~25k

SMD

17 * 30

IPEX/External/Spring

Summary of Contents for E30 Series





















Reviews: