1
Quick-start
Restore defaults
Scan the “Restore Custom defaults”.
Restore Custom defaults
Write to Custom Defaults
Quick-start : 2.4G/433M
The factory has been matched and you can use it directly.
Matching Operation
：
1, Press the button, the buzzer rang “Di-di-di” , the blue light is on, the scanner starts.
Note:
In the 2.4g mode of the Bluetooth scanner , the light is green.
2, Plug the dongle, the blue light is on, the Dongle starts to work.
3, Please match the dongle and the scanner within 30 seconds!
4, Open a text, put the cursor in, Scan your barcode.
Match
(match the scanner and the dongle)
Quick-start : Bluetooth
For Android
、
IOS
1
，
Press the button, the scanner starts
，
The red light flashing and the blue light is on which means in
matching mode.
2, The Scanner name
：
“Scanner xxx”, xxx is 3 random Numbers.
3, Choose the scanner is going to pair with the host
，
When the connection is successful, the red light goes
out and the blue light is on , the buzzer rang “DI-di”.
Recommending use 2.4G mode or wire-USB at the windows
！
1, Switch the Bluetooth scanner to 2.4G mode, plug in the 2.4G-dongle, and scan the "Match" Barcode.
2, Use the USB-cable to connect the computer.
General Settings
Match and Network
（
2.4G
，
433M
）
Match:
Plug the dongle to your computer
，
the system will automatically install the driver
，
when it start to
work , the blue light is always on
，
Match the scanner and the dongle by scan the “Match” Barcode.
(1) Matching successfully
：
the buzzer rang “ Di-da-di”, “DI-di-di”.
(2) Matching failed
：
the buzzer rang “ Di---en”.
If pairing fails, please unplug the dongle and try the matching operation again.
Network
：
One to one
，
More to one
One to one —one scanner to one dongle
1, Plug the dongle to your computer.
2, Scan the “Match” bar code to Match the dongle.
More to one —several scanners to one receiver.
Summary of Contents for EC-2D8380BT
