4
2, The scanner starts, when the buzzer rang “Di-di-di” and the blue light is on with the red light flashes three times, it indicates that the battery less than 20%,
please charge the scanner as soon as possible.
3, The scanner starts, when the buzzer rang “Di-di-di” and the blue light is on with the red light flashes three times, it indicates that the battery less than 5%, The
scanner enters the low battery protection mode. Please charge the scanner at least for 30 minutes.
4, Press the button, the scanner does not respond. Please charge the scanner at least for 30 minutes. If the scanner still cannot start, this indicates that the
battery is broken and needs to be replaced.
LED tips during charging
Plugged the USB cable into the USB port of computer.
1, Charging mode: the status light is on with the red light flashing.
2, Charging completed: the status light is on and the red light goes out.
3, Micro-current charging: the status light off and the red light flashing, this is battery protection phase, please do not use it in this condition.
Bluetooth- Setup
1, Bluetooth scanner has three modes: Bluetooth, 2.4G, Wire.
2, The default mode of the scanner is Bluetooth mode.
Press the button, the buzzer rang “Di-di-di”, The red light flashing and the blue light is on which means in matching mode
，
the green light is on
which means in 2.4G mode
，
Bluetooth/2.4G Switch operation
1: Press the button for 10seconds
，
2: Scan the settings barcode.
Bluetooth-mode
2.4G-mode*
Switch process description
In Bluetooth mode
，
Press and hold the button for 10seconds
，
the buzzer rang “ Di-da-di”, “DI-di-di”. Means that the switching operation is
complete
，
Release the button, The green light is on which means the scanner successfully switches to 2.4G-mode.
In 2.4G mode
，
Press and hold the button for 10seconds
，
the buzzer rang “ Di-da-di”, “DI-di-di”. Means that the switching operation is complete
，
Release the button, The blue light is on which means the scanner successfully switches to Bluetooth-mode.
Bluetooth Mode
Bluetooth-HID
Bluetooth-SPP
Bluetooth-BLE
IOS keyboard
Show/hide IOS keyboard
Note
：
Scan this barcode to show/hide the keyboard in IOS
Show/hide IOS keyboard
double-click –ON*
Show/hide IOS keyboard
double-click -OFF
Bluetooth connection settings
Off connection
Connection initialization
Buzzer setup
Turn on all sounds*
Turn off all sounds
Sound frequency 2048HZ
Sound frequency 2731HZ
Low volume
Medium volume
High volume *
Sound settings
Beep after good decode-ON*
Beep after good decode-OFF
Boot sound-ON*
Boot sound-OFF
Summary of Contents for EC-2D8380BT
