manualshive.com logo in svg

Ecco Axios, User Manual

Ecco Axios is an advanced electronic device that boasts cutting-edge features and exceptional performance. Equipped with an intuitive interface, this product simplifies your everyday tasks. To master all its capabilities, ensure you have the comprehensive user manual, available for free download exclusively at 88.208.23.73:8080.

Share
Download
background image

3

ENGLISH

ENGLISH

INSTALLATION & OPERATION INSTRUCTIONS

Components & Specification ......................................................................................................................... 4

    Unpacking & Pre-Installation

 .....................................................................................................................

4

    Specifications

 .............................................................................................................................................. 4

    Certifications

 .............................................................................................................................................. 4

Mounting ........................................................................................................................................................ 6

    

Permanent Mounting

 ................................................................................................................................

6

    Gutter Mounting

 ........................................................................................................................................

8

    Roof Mounting Kits .................................................................................................................................... 8

Wiring Instructions ........................................................................................................................................ 10

Programming & Operating  .......................................................................................................................... 12

    

Primary Warning & General Function ...................................................................................................... 12

    Safety Director Functions .......................................................................................................................... 13

    Scene Illumination Functions .................................................................................................................... 13

    Keypad Controller Mounting ................................................................................................................... 14

    Flash Pattern Chart .................................................................................................................................... 15

Assembly & Configuration ............................................................................................................................ 16

    Smart Chassis ............................................................................................................................................. 16

    Removing & Installing the Lens ................................................................................................................ 18

    Installing DropLock™ LED Modules ......................................................................................................... 20

          

Directional Modules (EZ1401X) .......................................................................................................... 20

          Beacon Modules (EZ1402X) ................................................................................................................ 22

          Worklamp Modules (EZ1403WL) ........................................................................................................ 24

          Alley Light Modules (EZ1403AL) ........................................................................................................ 26

          Stop-Tail-Indicator Modules (EZ1404) ................................................................................................ 28

          Safety Director™ (EZ1414) .................................................................................................................. 30

          Center Illumination (EZ1411).............................................................................................................. 32

Troubleshooting ............................................................................................................................................ 34

Warranty & Limitation of Liability ............................................................................................................... 35

Replacement Parts & Accessories ................................................................................................................. 36

Register Your Axios™ Modular LED Lightbar .............................................................................................. 36

INSTALLATION & 

OPERATION 

INSTRUCTIONS

Para ver este manual en español, vaya a 

AXIOS

MODULAR

.COM 

       

Pour consulter ce manuel en français, rendez-vous sur 

AXIOS

MODULAR

.COM

    

Um dieses Handbuch auf Deutsch zu lesen, besuchen Sie 

AXIOS

MODULAR

.COM

      

Per visualizzare il manuale in Italiano, visita 

AXIOS

MODULAR

.COM

3

Summary of Contents for Axios









































Reviews:

No comments

Related manuals for Axios

Garmin GHC 10 Quick Start Manual preview
GHC 10
Brand: Garmin Pages: 20
Kärcher R 100 Manual preview
R 100
Brand: Kärcher Pages: 20
Parker Research Corp B200S Operating Instructions preview
B200S
Brand: Parker Research Corp Pages: 3
Panasonic EU7805K Operating Instructions Manual preview
EU7805K
Brand: Panasonic Pages: 23
Y.I.C. TECHNOLOGIES EMScannerR Setup Manual preview
EMScannerR
Brand: Y.I.C. TECHNOLOGIES Pages: 6
Össur REBOUND DUAL ST Instructions For Use Manual preview
REBOUND DUAL ST
Brand: Össur Pages: 104
Össur OFM1 Instructions For Use Manual preview
OFM1
Brand: Össur Pages: 130
MacDon R1 FR Series Operator'S Manual preview
R1 FR Series
Brand: MacDon Pages: 238
Alpina SF-5098 Instructions For Use Manual preview
SF-5098
Brand: Alpina Pages: 24
Bird-X YARD GARD Instruction Manual preview
YARD GARD
Brand: Bird-X Pages: 2
Lightolier QVS2GPTLG232 Installation preview
QVS2GPTLG232
Brand: Lightolier Pages: 2
Beamz 151.265 Instruction Manual preview
151.265
Brand: Beamz Pages: 20
Furuno FCV-585 Operator'S Manual preview
FCV-585
Brand: Furuno Pages: 10
hager TN002S Quick Start Manual preview
TN002S
Brand: hager Pages: 2
Holland Green Science 10407001 User Manual preview
10407001
Brand: Holland Green Science Pages: 54
Launch Creader 319 Manual preview
Creader 319
Brand: Launch Pages: 16
Caloo CV-606 Instruction Manual preview
CV-606
Brand: Caloo Pages: 15
Dantel 46517-92 Installation & Operation Manual preview
46517-92
Brand: Dantel Pages: 46

Brands by name

Popular brands

Load more brands