English
English
15
favorite. During the search, the selected broadcast type will take precedence and the channels will be listed at
the top of the Channel List. When you're done, highlight the Next button and press
OK
to continue.
About the choice of the type of broadcast
To start searching for a certain type of broadcast, highlight it and press
OK
. The check box for the selected
option is selected. To turn off the search option, uncheck the box by pressing the
OK
button after moving your
attention to the desired broadcast type option.
Digital Antenna:
If the search option D is enabled. Antenna Broadcast, the TV will search for digital terrestrial
broadcasts after completing other initial settings.
Digital Cable:
If the search option D is enabled. Cable, after completing the other initial settings, the TV will
search for digital cable. Before you start the search, a message asks if you want to search the wired network. If
you select Yes and press
OK
, you can select Network or set values such as Frequency, Network ID and Search
Step on the following screen. If you select No and press
OK
, you will be able to set the Start Frequency, Stop
Frequency and Search Step on the following screen. When you're done, highlight the Next button and press
OK
to continue.
Note:
The search time varies according to the selected Search Steps.
Satellite:
If the Satellite search option is enabled, the TV will search for satellite digital broadcasts after
completing the other initial settings. Before performing a satellite search, you must make some settings. A
menu will appear where you can choose to start the M7 operator installation or the standard installation.
To start an M7 operator installation, set the Installation Type as Operator and the Satellite Operator as the
appropriate M7 operator. Then highlight the Scan Preferences option and set as Auto Channel Tuning and
press
OK
to start the automatic search. These options can be pre-selected depending on the Language and
Country options you selected in the previous steps of the Initial Installation process. You may be prompted to
select the HD/SD list or channel list by country, depending on your M7 operator type. Choose one of them and
press
OK
to continue.
Wait for the scan to finish. Now the list is installed.
During the M7 operator installation procedure, if you want to use satellite installation parameters that differ
from the default settings, select Preferred Scan as Manual Program Search and press
OK
to continue. The
Antenna Type will then be displayed. After selecting the antenna type and the desired satellite in the following
steps, press the
OK
button to change the installation parameter of the satellite in the inserted menu.
To search for other channels, such as M7 channels, you must run the standard installation. Select Installation
Type as Standard and press
OK
to continue. The Antenna Type will then be displayed.
There are three options for antenna selection. You can select the antenna type as Direct, Simple Satellite Cable
System or DiSEqC switch by using the Left or Right buttons. To view the subsequent options, after selecting
your antenna, press
OK
. The Continue options will appear,
Transponder List and LNB Configuration
Use the related menu options to change the transponder and LNB settings.
•
Right:
If you have a single receiver and a direct satellite dish, select this type of antenna. Press
OK
to
continue. On the following screen, select an available satellite and press
OK
to search for services.
•
Simple satellite cable system:
Choose this type of antenna if you have multiple receivers and a simple
satellite cable system. Press
OK
to continue. Configure the settings as instructed on the following screen.
Press
OK
to search for services.
•
DiSEqC switch:
If you have multiple satellites and a DiSEqC switch, select this antenna type. Then set
the DiSEqC version and continue by pressing the
OK
button. On the next screen you can set up to four
satellites (if available) for v1.0 and sixteen satellites for v1.1. Press
OK
to scan the first satellite in the list.
Analog:
If the Analog search option is enabled, the TV will search for Analog broadcasts after completing the
other initial settings. Once the initial settings are complete, the TV will begin searching for available broadcasts
of the selected broadcast types. During the search, the current results will be displayed at the bottom of the
screen. Once all available stations have been saved, the Channels menu will appear. Here you can edit the
channel list according to your preferences using the Edit tab options, or press the
Menu
button to exit and
view the TV broadcast.
