background image

STANDARD SYSTEM FEATURES 

 

Aluminum vertical frame

 with shock mounted Duplex stainless steel high pressure pump, control panels 

and RO vessels 
 
2 Filter housings with pleated polyester cartridges, 5 and 20 microns, 41/2” x 10” 

1 Filter wrench 
 
Manual fresh water flush system 

Pressure vessel(s) with reverse osmosis membrane(s) 

ECH

2

O Tec. 

1000-BHL-2  two 

40” vessels 

 

1300-BHL-3  three 

40” vessels 

 

1800-BHL-4  four 

40” vessels 

Instruments

 

 
The desalination system is equipped with all necessary instrumentation, for the control and supervision of 
the operation of the unit.  
The instrumentation includes: 

Pressure Gauges:

 

   Feed water, system entrance (316SS glycerin filled) 

  

   Feed water, high pressure pump entrance (316SS glycerin filled) 

  

   RO pressure, (316SS glycerin filled) 

  

     

Flow Meter:

 

   Product discharge 

Conductivity: 

 

   Digital product water quality monitor - ppm TDS 

The following automatic emergency shut off functions are provided:  

Low feed water pressure (e.g. seawater intake or pre-filters clogged) 
High RO pressure 
Tank full (float switch optional) 

 

1    Fresh water flush filter with active carbon cartridge 
 

1    Hardener / pH neutralizer kit

 with mineral element and 2pcs 3/8” compression fittings 

1    Stainless steel bracket with 8 screws

 

 
20 feet / 6 meter 1/2” reinforced vinyl hose (reject, product, flush) 

 10 feet / 3 meter blue product water tubing (membrane to flow panel) 
 10 feet / 3 meter 3/4” reinforced vinyl hose (pre-filter to high pressure pump) 

 3  feet / .9 meter 5/8” service intake hose 
 

 

6   1/2" Stainless steel hose clamps  
1   5/8” Stainless steel hose clamp 
2   3/4” Stainless steel hose clamps  
 
1   Handheld TDS Meter 
1   Biocide, 1 acid cleaning solution, 1 alkaline cleaning solution 
1   Owners Manual 

Summary of Contents for 1000-BHL- 2


















Reviews: