background image

The ECHO Tec. Membrane Element is guaranteed to be cleanable for a minimum of one year from date 
of  shipment,  provided  that  cleaning  instructions  are  adhered  to  and  foulant  is  acid  soluble  metal 
hydroxides  and  calcium  carbonates  or  alkaline  soluble  organic,  inorganic  substances  and 
microbiological  slimes.    The  ECHO  Tec.  Membrane  Element  is  not  guaranteed  against  iron  fouling 
(rust),  chemical  attack,  extreme  temperatures  (over  120º  F/under  32ºF),  drying  out,  or  extreme 
pressures (over 1000 psig). 
 
 
Boat building or refurbishing is a timely process and unexpected delays can occur.   
ECHO  Tec.  Systems  are  normally  shipped  complete  with  Reverse  Osmosis  Membrane  Element(s).  
However,  if  the  ECHO  Tec.  System  will  not  be  put  to  use  within  9  months  of  shipment,  there  is  a 
potential  danger of the Reverse Osmosis Membrane Element(s) fouling or drying out.  Therefore, we 
can ship your system without the Membrane(s).  This allows you to install the system at the appropriate 
time  in  your  scheduled  production/refurbishing  without  damage  to  the  Reverse  Osmosis  Membrane 
Element(s).    We  will  ship  the  Reverse  Osmosis  Membrane  Element(s)  when  notified  that  the  ECHO 
Tec. System is ready for use.  This service is available upon request only. 
 
 
The  warranty  on  the  ECHO  Tec.  Watermaker  is  activated  upon  shipment  of  the  system  with  the 
Reverse Osmosis Membrane Element(s) pre-installed.  However, by shipping the watermaker without 
the  Reverse  Osmosis  Membrane  Element(s),  the  warranty  period  will  start  upon  shipment  of  the 
Reverse  Osmosis  Membrane  Element(s),  with  a  delay  of  12  months  maximum  from  the  date  of 
purchase. 
 
 

ECHO MARINE LTD. 

1

st

 Avenue South, 

Chaguaramas 
Trinidad W.I. 

 
 

TELEPHONE: 1-868-634-2027 

FAX: 1-868-634-2026 

E-MAIL: echotec@echo-marine.com 

 

 

www.ech2otec.com

 

Summary of Contents for Watermakers 1200-BML-3






















Reviews: