background image

ECH

2

O TEC. WATERMAKER LIMITED WARRANTY 

 

Echo Marine Ltd. for a period of thirty-six (36) months from the date of shipment that the ECHO Tec. 
watermaker will perform according to specifications.  The triplex plunger high-pressure pump and the 
high  pressure  vessel/s  are  guaranteed  for  life  to  the  original  purchaser.  Echo  Marine’s  liability  under 
this warranty shall be limited to repair or replacement of the ECHO Tec. watermaker at Echo Marine’s 
option. Under no circumstances shall Echo Marine Ltd. be liable for consequential damages arising out 
of or in any way connected with the failure of the system to perform as set forth herein.  This limited 
warranty is in lieu of all other expressed or implied warranties, including those of merchantability and 
fitness for a particular purpose. 
 
 
In the event of a defect, malfunction, or failure during the warranty period, Echo Marine Ltd. will repair 
or replace, at its option, the product or component therein which, upon examination by Echo Marine, 
shall appear to be defective, or not up to factory specifications. 
 
 
To  obtain  warranty  service,  the  defective  product  or  part  must  be  returned  to  Echo  Marine’s  Service 
Center.    The  purchaser  must  pay  any  transportation  or  labor  expenses  incurred  in  removing  and 
returning the product. A return authorization must be obtained before any part or component is shipped.  
 
 
The  limited  warranty  does  not  extend  to  any  system  component  that  has  been  subjected  to  misuse, 
neglect, accident, improper installation, or used in violation of instructions furnished by Echo Marine 
Ltd.  The  warranty  does  not  extend  to  components  on  which  the  serial  number  has  been  removed, 
defaced or changed. 
 
 
Echo Marine Ltd. reserves the right to make changes or improvements in its product during subsequent 
production  without  incurring  the  obligation  to  install  such  changes  or  improvements  on  previously 
manufactured equipment. 
 
 
The implied warranties, which the law imposes on the sale of this product, are expressly LIMITED, in 
duration  to  the  time  period  above.    Echo  Marine  shall  not  be  liable  for  damages,  consequential  or 
otherwise,  resulting  from  the  use  and  operation  of  this  product  or  from  the  breach  of  this  LIMITED 
WARRANTY. 
 
This limited warranty service does not apply to normal recurring user maintenance as described below. 
 
 

  Sea Strainer Element   

 

  Pump Valve Assemblies        

              Pre-filter Cartridges                               Gauge Instrument Calibration 
 

  Auxiliary Tubing 

 

 

  Pump Crankcase Oil 

 

  Pump Seals and Packings         

  V or Timing Belt 

 

  Pump Bushings and Bearings  

   

 

   

 

 

 

 

   

 

   

Summary of Contents for Watermakers 200-BMS-1






















Reviews: