background image

8

S

PECIFICATIONS

MODEL ----------------------------------------------------- ES-231 SHRED 'N' VAC

®

Length ------------------------------------------------------- 335 mm (13.2 in.) (w/o blower pipes)

Width (w/rear handle) ------------------------------------- 305 mm  (12.0 in.)

Height ------------------------------------------------------- 375 mm (14.8 in.) (in blower configuration w/side handle)

Weight (dry) ------------------------------------------------ 4.9 kg (10.8 lb.)(w/o blower pipes)

Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine

Displacement ----------------------------------------------- 22.8 cc (1.39 cu. in.)

Bore ---------------------------------------------------------- 32.2 mm (1.27 in.)

Stroke -------------------------------------------------------- 28.0 mm (1.10 in.)

Carburetor -------------------------------------------------- Zama Diaphragm, model RB  w/primer bulb

Ignition System -------------------------------------------- Flywheel Magneto, capacitor discharge ignition type

Spark Plug -------------------------------------------------- NGK BPM-8Y Gap 0.65 mm (0.026 in.)

Exhaust System -------------------------------------------- Spark Arrestor Muffler w / Catayst

Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil)

Fuel/Oil Ratio ----------------------------------------------- 50:1 two-stroke air cooled engine oil

Gasoline ----------------------------------------------------- 89 Octane unleaded. DO NOT use fuel containing methyl alcohol,

more than 10% ethyl alcohol or 15% MTBE.

Oil ------------------------------------------------------------ Power Blend 

TM

 Premium Universal 2-Stroke Oil

Fuel Tank Capacity ---------------------------------------- 0.6 lit. (20.3 US fl. oz.)

Recoil Starter System -------------------------------------- Automatic Recoil Starter Centrifugal Type

Wide Open Throttle Speed (RPM) ----------------------- 7000 - 8500

Idle Speed (RPM) ------------------------------------------ 2400 - 3200

Maximum Air Volume -------------------------------------- 9.1  m3/min. (321 cu. ft./min.)

Maximum Air Speed w/pipes (MPH) -------------------- 76 m/sec  (170 mph)

Sound Level at 50 ft. dB(A) scale per ANSI B175.2 ---- 70 dB(A)

Summary of Contents for 06001247


























Reviews: