EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
English
35
WARNING!
Servicing requires extreme care and knowledge
and should be performed only by a quali
fi
ed service
technician. For service, bring the product to an
authorised service centre for repair. When servicing,
use only original replacement parts.
WARNING!
Remove the battery before adjustment, maintenance
or cleaning. Failure to do so could result in serious
personal injury.
■
You may only make adjustments or repairs described
in this manual. For other repairs, contact the authorised
service agent.
■
Consequences of improper maintenance may cause
the chain brake and other safety features to not function
correctly, thus increasing the potential for serious
injury. Keep your chainsaw professionally maintained
and safe.
■
Sharpening the chain safely is a skilled task. Therefore,
the manufacturer strongly recommends that a worn or
dull chain is replaced with a new one, available at your
authorised service centre. The part number is available
in the product specification table in this manual.
■
Follow instructions for lubricating and chain tension
checking and adjustment.
■
After each use, clean the product with a soft dry cloth.
■
Check all nuts, bolts, and screws at frequent intervals
for security to ensure the product is in safe working
condition. Any part that is damaged should be properly
repaired or replaced by an authorised service centre.
Replacing guide bar and saw chain
See pages 10 - 13.
Make sure to remove the battery. Wear protective gloves.
Remove the bar mounting nuts using the combination
wrench provided.
Remove the chain cover.
Remove the bar and saw chain from the product.
Put the new chain in the correct direction onto the bar and
make sure that the drive links are aligned in the bar groove.
Attach the bar to the chain saw and loop the chain around
the drive sprocket.
Replace the chain cover and bar mounting nuts.
Finger-tighten the bar mounting nuts. The bar must be free
to move for chain tension adjustment.
Adjust the chain tension. Refer to the “Adjusting chain
tension” section.
Hold the tip of the guide bar up and tighten the bar mounting
nuts securely.
Inspecting and cleaning the chain brake
See page 22.
Always keep the chain brake mechanism clean by lightly
brushing the linkage free from dirt.
Always test the chain brake performance after cleaning.
Refer to “Checking and operating the chain brake” section
in this manual for additional information.
MAINTENANCE SCHEDULE
Daily check
Bar lubrication
Before each use
Chain tension
Before each use and
frequently
Chain sharpness
Before each use, visual
check
For damaged parts
Before each use
For loose fasteners
Before each use
Chain brake function
Before each use
Inspect and clean
Bar
Before each use
Complete saw
After each use
Chain brake
Every 5 hours*
* Hours of operation
REPLACEMENT PARTS
Part
Accessory number
Guide bar
6000945
Chain
90PX056X
BATTERIES
■
Battery packs, which have not been used for some time
should be recharged before use.
■
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended
exposure to heat or sunshine (risk of overheating).
■
The contacts of chargers and battery packs must be
kept clean.
■
For an optimum lifetime, the battery packs have to be
fully charged after use.
■
To obtain the longest possible battery life, remove the
battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
■
Store the battery pack where the temperature is below
27°C and away from moisture.
■
Store the battery pack in a 30% - 50% charged
condition.
Summary of Contents for 4892210170330
