background image

LIMITED WARRANTY

This warranty applies to all ECHO Bear Cat Outdoor Power Equipment manufactured by Crary Industries, Inc. 

and does not include gas engine or electric powered pressure washers under the ECHO Bear Cat brand. See 

ECHO Bear Cat Pressure Washer Limited Warranty for complete warranty details on those products.
Crary Industries, Inc. warrants to the original owner each new ECHO Bear Cat product to be free from defects 

in material and workmanship, under normal use and service. The warranty shall extend, from date of purchase, 

3 years (U.S. and Canada only (2 years outside U.S. and Canada)) for Consumer use of the product, 1 year 

for Commercial applications and 6 months for Rental applications. Replacement parts and accessories are 

warranted for (90) days from date of installation. Batteries for Inverters and Generators are warranted for ninety 

(90) days from the date of purchase.

"Consumer" defined as: complete unit for personal, residential or non-income producing use.
"Commercial"  defined  as:  complete  unit  for  commercial,  institutional,  property  management,  agricultural, 

horticultural or income producing use.

"Rental" defined as: complete unit for rental purposes to produce income.
*Models  SC2163,  SC2170  &  SC3206  are  classified  as  Consumer  grade  products  and  will  not  qualify  for 

warranty coverage if used for Commercial or Rental purposes.

The product is warranted to the original owner by either a completed warranty registration on file at Crary 

Industries, Inc. and/or proof of sale. Warranty coverage begins on the date of purchase. The warranty 

registration can be registered on-line by visiting http://bearcatproducts.com/warranty/warrantyregistration/ or 

the paper card completed and returned to Crary Industries, Inc.
In the event of a failure, return the product, at your cost, along with proof of purchase to the selling ECHO Bear 

Cat dealer. Crary Industries, Inc. will, at its option, repair or replace any parts found to be defective in material 

or workmanship. Warranty on any repairs will not extend beyond the product warranty. Repair or attempted 

repair by anyone other than an authorized ECHO Bear Cat dealer as well as subsequent failure or damage that 

may occur as a result of that work will not be paid under this warranty. Crary Industries, Inc. does not warrant 

replacement components not manufactured or sold by Crary Industries, Inc.
1.  This warranty applies only to parts or components that are defective in material or workmanship.
2. 

This warranty does not cover normal wear items including, but not limited to: batteries, bearings, belts, 

pulleys, filters, chipper blades, shredder flails or knives.

3.  This warranty does not cover normal maintenance, service or adjustments.
4.  This warranty does not cover depreciation or damage due to misuse, negligence, accident or improper 

maintenance.

5.  This warranty does not cover damage due to improper setup, installation or adjustment.
6. 

This warranty does not cover damage due to unauthorized modifications of the product. 

7.  Engines are warranted by the respective engine manufacturer and are not covered by this warranty.
Crary Industries, Inc. is not liable for any property damage, personal injury or death resulting from the 

unauthorized modification or alteration of an ECHO Bear Cat product or from the owner's failure to assemble, 

install, maintain or operate the product in accordance with the provisions of the Owner's manual.

Crary Industries, Inc. is not liable for indirect, incidental or consequential damages or injuries including but not 

limited to loss of crops, loss of profits, rental of substitute equipment or other commercial loss.
This warranty gives you specific legal rights. You may have other rights that may vary from area to area.

Crary Industries, Inc. makes no warranties, representations or promises, expressed or implied as to the 

performance of its products other than those set forth in this warranty. Neither the dealer nor any other person 

has any authority to make any representations, warranties or promises on behalf of Crary Industries, Inc. 

or to modify the terms or limitations of this warranty in any way. Crary Industries, Inc., at its discretion, may 

periodically offer limited, written enhancements to this warranty.

CRARY INDUSTRIES, INC. RESERVES THE RIGHT TO CHANGE THE DESIGN AND/OR 

SPECIFICATIONS OF ITS PRODUCTS AT ANY TIME WITHOUT OBLIGATION TO PREVIOUS 

PURCHASERS OF ITS PRODUCTS.

ENGLISH

Summary of Contents for BEAR CAT CH6720H








































Reviews: