background image

17

5 INCH CHIPPER/SHREDDER

ENGLISH

Section

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSES

REMEDY

Engine or rotor stalls or 

stops

Chipper rotor housing or discharge tube is 

plugged

Shut off engine and disengage belt 

engagement. Refer to manual for 

information on clearing a plugged rotor. 

Never use the belt engagement to clear a 

plugged rotor.

Feeding material that is too large

Limit branch size to rated capacity

Machine chips poorly

Dull chipper blades

Flip, sharpen, or replace

Drive belts loose or worn

Inspect drive belts, adjust or replace if 

needed

Feeding material that is too large

Limit branch size to rated capacity

Hard to feed chipper, 

requires excessive 

power to chip

Dull chipper blades

Flip, sharpen, or replace

Obstructed discharge

Use branch or similar object to clear 

discharge tube

Improper blade clearance

Set blade/anvil clearance to recommended 

distance

Shredder requires 

excessive power or 

stalls.

Obstructed discharge

Use branch or similar object to clear 

discharge tube

Plugged rotor

Clear rotor, feed material into shredder 

more evenly

Wet or green material will not discharge

Alternately feed dry material or install larger 

discharge screen

Engine stalls or 

belt squeals when 

engaging belt

Engaging belt too fast

Reduce engagement speed

Belt tension too loose

Adjust tensioner. Replace belt if needed.

Material from chipper 

wraps around rotor 

shaft

Stringy, green material bypasses chipper 

blades

Rotate branch or material when feeding to 

cut completely

Dull chipper blades

Flip, sharpen, or replace

Improper blade clearance

Set blade/anvil clearance to recommended 

distance

Before performing any of the corrections in this troubleshooting chart, refer to the appropriate information contained in 

this manual for the correct safety precautions and operating or maintenance procedures. Contact your dealer or ECHO 

Bear Cat

®

 for service problems with the machine.

Summary of Contents for BEARCAT SC5540



























Reviews: