Echo CS-530 Instruction Manual Download

Page: 32 / 32

CS-530

STORAGE AFTER USE

TECHNICAL DATA

• Inspect and adjust every part of the chain saw.

- Completely clean every part and repair if

necessary.

- Apply thin coating of oil on metal parts to

prevent rust.

• Remove chain and guide bar.
• Drain fuel tank, pull starter slowly a few times to

drain fuel from carburetor.

• Pour a small amount of clean motor oil into spark

plug hole, pull starter and crank the engine until
piston reaches: TOP DEAD CENTER.

• Store in a dry area, free from dust.

WARNING

Do not store in an enclosure where fuel
fumes may accumlate or reach an open flame
or spark.

CAUTION

Do not lend or rent your chain saw without
the Instruction manual and Safety manual.

NOTE

• For future reference, you should keep this

Instruction manual and the Safety manual.

• If this Instruction manual or the Safety manual

has become illegible or is lost, please purchase
a new one from your ECHO dealer.

CS-530

Dimension

L × W × H

400 × 252 × 278 (15.7 in. × 9.9 in. × 10.9 in.)

Mass

Power head, dry

5.1 (11.2 lb.) Without chain and guide bar

Engine

Type

Air-cooled two-stroke single cylinder

Displacement

mL (cm³)

50.1 (3.057 cu. in.)

Carburetor

Diaphragm type

Magneto

Flywheel magneto: CDI system

Spark plug

NGK BPM8Y

Starter

Recoil starter

Power transmission

Automatic centrifugal clutch

Fuel

Mixture ratio

50 : 1 ratio with ECHO Power Blend X™, ISO-L-EGD
(ISO/CD 13738), JASO M345-FC/FD two- stroke,
air-cooled engine oil.

Gasoline

Use 89 octane unleaded.
Do not use fuel containing methyl alcohol, more than
10 % ethyl alcohol or 15 % MTBE.
Do not use alternative fuels such as E-20 or E-85.

Tank capacity

0.60 (20.3 US. fl. oz.)

Oil

Bar and chain

ECHO bar and chain oil (or motor oil)

Tank capacity

0.28 (9.5 US. fl. oz.)

Guide bar and

See page 22 for Chain and Guide Bar Combination

saw chain

Lubrication

Adjustable automatic oil pump

Engine speed

Idle

r/min

2800

Clutch engagement

r/min

3800

Wide open throttle

r/min

13500

Standard

Front hand guard, Rear hand guard,

features

Anti-vibration device, Spiked bumper,
Throttle control lockout, Chain brake,
Chain catcher, Spark arrestor muffler, Kick guard

* Technical data subject to change without notice.

Summary of Contents for CS-530

































Search results

Summary of Contents for CS-530

Reviews:

Related manuals for CS-530

Brands by name

Popular brands

Echo CS-530, Instruction Manual

Search results

Summary of Contents for CS-530

Reviews:

Related manuals for CS-530

Brands by name

Popular brands