background image

2

WARNING         DANGER

ALWAYS STOP THE ENGINE WHEN A DRILL
JAM OCCURS. DO NOT ATTEMPT TO
REMOVE AN OBJECT CAUSING A DRILL
JAM IF THE ENGINE IS RUNNING. PHYSICAL
INJURY CAN OCCUR IF A DRILL JAM IS
REMOVED AND THE DRILLS START
MOVING.

Do all drilling at full throttle speed. Drilling at
less at than full speed can damage the clutch
by allowing it to slip.

WARNING         DANGER

USE A FIRM GRIP WITH THUMBS AND
FINGERS ENCIRCLING THE HANDLES. A
FIRM GRIP WILL HELP YOU KEEP CONTROL
OF THE ENGINE DRILL. NEVER OPERATE
THE ENGINE DRILL ONLY ONE HAND OR
BODILY INJURY CAN OCCUR.

Always carry the engine drill with the engine
stopped and the HOT muffler away from your
body.

PROTECTIVE EQUIPMENT

Always wear eye protection goggles that meet
ANSI Z87.1 standards.

Wear hearing protection.
ECHO recommends that hearing protection be
worn at all times.

Dress properly! Do not wear loose clothing or
jewellery, they can be caught in moving parts.
Use of sturdy gloves, non-skid footwear, and
safety glasses is recommended.

While operating the machine always be sure of
a secure position.

WARNING         DANGER

ENGINE DRILL USERS RISK INJURY TO
THEMSELVES AND OTHERS IF THE ENGINE
DRILL IS USED IMPROPERLY, AND/OR
SAFETY PRECAUTIONS ARE NOT
FOLLOWED. PROPER CLOTHING AND
SAFETY GEAR MUST BE WORN WHEN
OPERATING ENGINE DRILL.

OPERATOR SAFETY

Read this Engine drill Operator’s Manual
carefully. Be sure you understand how to
operate this unit properly before you use it.

Be familiar with all the controls and the proper
use of the machine.

Wear proper clothing to protect legs and other
exposed parts of your body.

Wear non-skid sole shoes. Do not wear open-
toed shoes or operate unit while bare footed.

Wear eye and hearing protection devices.

Use caution when handling fuel. Put the caps
back tightly on both the fuel can and the engine
drill fuel tank.
Move at least 3 m (10 feet) from the refueling
point and be sure there is no leakage of fuel
from the fuel tank cap or the fuel system before
starting the engine.

Operate this gasoline powered engine
equipment in a well-ventilated area only.

Start the unit on the ground with the throttle set
at idle. Do not start if the drills are obstructed
by the ground or any other object.

Never allow children to use the machine.

Do not allow anyone to hold the material you
are drilling.

Keep a firm grip on the engine drill with both
hands, the right hand on the front handle, the
left hand on the rear handle.

SAFETY

Summary of Contents for ED-200

















Reviews: