background image

G

RASS

 T

RIMMER

O

PERATOR

'

S

 M

ANUAL

15

STARTING

 

WARM

 

ENGINE

The starting procedure is the same as Cold Start except DO NOT close
the choke, and do not depress throttle trigger to wide open position.

    WARNING   

   DANGER

The attachment should not move at idle, otherwise serious personal
injury may result.

NOTE
If attachment moves, readjust carburetor according to “Carburetor
Adjustment” instructions in this manual or see your ECHO Dealer.

1. Stop Switch

Move stop switch (A) away from the STOP position

2. Primer

Pump primer bulb (C) until fuel will be visible and flows freely in
the clear fuel tank return line. Pump bulb an additional 4 or 5
times.

3. Recoil Starter

Lay the unit on a flat area and keep movable attachment parts clear
of all obstacles. Rapidly pull recoil starter handle/rope (D) until
engine fires.

 NOTE
If engine does not start after 5 pulls, use Cold Start Procedure.

STOPPING

 

ENGINE

1.

Throttle
Release throttle and allow engine to return to idle before shutting
off engine.

2.

Stop Switch
Move stop switch button (A) backward to STOP position.

WARNING  

  DANGER

If engine does not stop when stop switch is moved to STOP
position, close choke - COLD START position - to stall engine.
Have your ECHO dealer repair stop switch before using trimmer
again.

D

A

C

A

Summary of Contents for GT-200R - 11-03

























Reviews: