background image

ECHO, INCORPORATED

400 O

AKWOOD

 R

OAD

L

AKE

 Z

URICH

, IL  60047

DEALER?

Call

1-800-432-ECHO

ECHO,

 

 Incorporated

400 Oakwood Road

Lake Zurich, IL  60047

Technical Publications Orders

CONSUMER PRODUCT

SUPPORT

1-800-673-1558

8 - 5 Mon - Fri C.S.T.

S

ERVICING

 I

NFORMATION

PARTS

Genuine ECHO Parts and ECHO REPOWER

 Parts and Assemblies

for your ECHO products are available only from an Authorized ECHO
Dealer.  When you do need to buy parts always have the Model
Number, Type number and Serial Number of the unit with you.  You
can find all three numbers on the engine housing.  For future reference,
write them in the space provided below.

Model No. _____________ Type No. _________SN. ____________

SERVICE

Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer.  For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246) When presenting your unit for Warranty
service/repairs, proof of purchase is required.

ECHO

 

CONSUMER

 

PRODUCT

 

SUPPORT

If you require assistance or have questions concerning the application,
operation or maintenance of this product you may call the ECHO
Consumer Product Support Department at 1-800-673-1558 from 8:00 am
to 5:00 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.

WARRANTY

 

CARD

This card is our means of registering all original owners of ECHO
equipment.  The card plus proof of purchase provides you the assur-
ance that authorized warranty work will be done.  It also provides a
direct link between you and ECHO if we find it necessary to contact
you.

ADDITIONAL

 

OR

 

REPLACEMENT

 

MANUALS

Safety Manuals  are available, free of charge, from your ECHO dealer or
by contacting Echo Incorporated, 400 Oakwood Road, Lake Zurich, IL
60047.
Operator's and Parts Manuals are available for purchase from your
ECHO dealer or directly from ECHO. [See ordering instructions below.]

ORDERING

 

INSTRUCTIONS

To obtain a Parts Catalog or Operator's Manual send a check or money
order for $2.00 per Parts Catalog or $1.50 per Operator's Manual made
payable to ECHO, INCORPORATED.  State on a sheet of paper the
model number and serial number of the ECHO unit you have, part
number of the manual (if known), your name and address and mail to
address above.

Available Parts Catalog

SHC-1700 Type 1/1E S/N 001001 & Up

99922202849

SHC-2100 Type 1/1E S/N 001001 & Up

99922202850

SHC-2400 Type 1/1E S/N 001001 & Up

99922202851

HCA-2400 Type 1/1E S/N 001001 & Up

99922202852

Summary of Contents for HCA-2400





































Reviews: