© 06/2020 ECHO Incorporated X7152270100
24
QUICK START GUIDE / GUÍA DE INICIO RÁPIDO / GUIDE DE DÉMARRAGE
RAPIDE
PAS-225 / PAS-2620
Pro Attachment Series
™
EMISSIONS CONTROL COMPONENTS
The use of emission control components other than those specifically
designed for this unit is a violation of federal law.
Maintain Air Filter
1. Close choke, remove air filter cover, clean air cleaner area, clean or replace
filter (if damaged).
Maintain Spark Plug
Note: PAS-225; Use only NGK BPM8Y (BPMR8Y in Canada) spark plug
otherwise severe engine damage can occur.
PAS-2620; Use only NGK CMR7H spark plug otherwise severe engine
damage can occur.
1. Adjust spark plug gap by bending outer electrode to a 0.65 mm (0.026 in)
gap.
2. Tighten spark plug to 150 - 170 kgf•cm (130 - 150 in•lbf).
Maintain Spark Arrestor Screen
Parts Required: Spark Arrestor Screen, Gasket
1. Remove spark plug lead and engine cover or muffler cover if applicable.
2. Place piston at Top Dead Center (TDC) to prevent carbon/dirt from entering
cylinder.
3. Remove spark arrestor screen cover, gaskets, and screen, from muffler
body.
4. Clean carbon deposits from muffler components.
Note: When cleaning carbon deposit, be careful, do not damage the catalytic
element inside muffler (If equipped with catalytic element).
5. Replace screen if it is cracked, plugged, or has holes burned through.
6. Assemble components in reverse order.
Fuel is VERY flammable. Use extreme care when mixing, storing or
handling, or serious personal injury will result.
Maintain Fuel Filter
1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel
tank. Pull the fuel filter from the fuel tank. Remove the filter from the line
and install the new filter (do not damage fuel line when removing the fuel
filter from the tank).
EMISSION CONTROL (EXHAUST & EVAPORATIVE)
• CARB and EPA Emissions Control Information.
•
The emission control system for the engine is EM (engine modification) and,
if the second to last character of the Engine Family on the Emission Control
Information label (sample below) is “B”, “C”, “K”, or “T”, the emission control
system is EM and TWC (3-way catalyst). The fuel tank/fuel line emission
control system is EVAP (evaporative emissions). Evaporative emissions for
California models are only applicable to fuel tanks and fuel feed lines.
• An Emission Control Label is located on the engine. (This is an EXAMPLE
ONLY, information on label varies by ENGINE FAMILY).
• Product Emission Durability (Emission Compliance Period).
• The 50 or 300 hour emission compliance period is the time span selected
by the manufacturer certifying the engine emissions output meets applicable
emissions regulations, provided that approved maintenance procedures are
followed as listed in the Maintenance Section of this manual.
SERVICE
• Service of this product during the warranty period must be performed by
an Authorized ECHO Service Dealer. For the name and address of the
Authorized ECHO Service Dealer nearest you, ask your retailer or call
1-800-432-ECHO (3246). Dealer information is also available on our Web
Site www.echo-usa.com. When presenting your unit for Warranty service/
repairs, proof of purchase is required.
Cancer and Reproductive Harm.
www.P65Warnings.ca.gov
Transportation
•
During operation the muffler or catalytic muffler and surrounding cover
can become hot. Always keep exhaust area clear of flammable debris
during transportation or when storing, otherwise serious property
damage or personal injury can result.
• Always secure the unit during transportation to prevent turnover, fuel
spillage, and damage to the unit.
Short-term Storage
• Store unit in a dry, dust free place, out of the reach of children.
• Do not store in enclosure where fuel fumes can accumulate or reach an
open flame or spark, or serious personal injury will result.
Long-term Storage (Over 30 Days)
• Place the stop switch in the “OFF” position.
•
Clean the exterior of the product.
• Perform all periodic maintenance.
• Tighten all the screws and nuts.
• Drain the fuel and run the unit until it stops.
• Allow engine to cool.
• Store unit in a dry, dust free place, out of the reach of children.
Storage Hook Installation
1. Insert small end of hook into locating hole on
attachment shaft.
2. Slide plastic cap onto end of attachment shaft.
