background image

9

P

ower

 B

lower

 

o

Perator

'

s

 M

anual

NOTICE:

 Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor 

performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage 

section of this manual.

fuel

  

 WARNING 

Alternative fuels, such as E-20 (20% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are 

NOT

 approved for use in ECHO 2-stroke gasoline engines.  Use of alternative fuels may cause performance prob

-

lems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to, 

improper clutch engagement.  Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carbu-

retors and other engine components.

 

a

ssembly

  

  WARNING   

Never perform maintenance or assembly procedures with engine 

running or serious personal injury may result.

bloWer

 

applIcatIon

Install Blower Pipes 

  1.  Align grooves in straight pipe with pegs on blower housing and 

slide pipe onto housing.

  2.  Turn straight pipe clockwise to lock into place.

  3.  Align grooves in fan head nozzle with pegs on straight pipe and 

slide fan head nozzle onto straight pipe.

  4.  Turn fan head nozzle clockwise to lock into place.

o

peratIon

 

WARNING

Moving parts can amputate fingers or cause severe injuries.  Keep hands, clothing and loose objects away from all 

openings.  Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop 

before removing obstructions, clearing debris, or servicing unit. Blower housing may contain shredder blades and 

other sharp edges that can cause serious injuries if touched, even if engine is off and blades are not moving.  Wear 

gloves to protect hands from sharp edges and hot surfaces. 

  

  WARNING

Operation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped with 

a spark arrestor and a spark arrestor may be required.  The operator should contact local fire agencies for laws or 

regulations relating to fire prevention requirements.

Summary of Contents for PB-200 - 02-09

























Reviews: