background image

SERVICE INFORMATION

PB-655
PB-755

2

1  SERVICE INFORMATION

1-1 Specifications

Model

PB-655

PB-755

Dimensions Length*

mm(in)

380 (15.0)

Width*

mm(in)

480 (18.9)

Height*

mm(in)

525 (20.7)

Dry weight**

kg(lb)

11.3 (24.89)

11.9 (26.21)

Engine

Type

KIORITZ, air-cooled, two-stroke, single cylinder

Rotation

Anticlockwise as viewed from the output end

Displacement

cm

3

(in

3

)

63.3 (3.86)

Bore

mm(in)

48.0 (1.89)

Stroke

mm(in)

35.0 (1.38)

Compression ratio

6.3

Carburettor

Type

Diaphragm, horizontal-draught, with primer

Model

Walbro WYK-192

Ignition

Type

CDI (Capacitor discharge ignition) system

Spark plug

BPM8Y

Exhaust

Muffler type

Spark arrestor muffler

Starter

Type

Automatic rewind

Rope diameter x length

mm(in)

3.5 x 1000 (9/64 x 39 1/2)

Fuel

Type

Premixed two-stroke fuel

Mixture ratio

50 : 1 (2 %)

Petrol

Minimum 89 octane unleaded

Two-stroke air cooled engine oil

ISO-L-EGD (ISO/CD13738),  JASO FC/FD

Tank capacity

L (U.S.fl.oz.)

2.0 (67.7)

Throttle

Mount

Tube-mounted throttle with cruise control

Blower

Fan type

Centrifugal, single stage

Max. air volume (with pipes)

m

3

/min (ft

3

/min)

17.7 (625)**

Max. air velocity (with pipes)

m/s (mph)

 92 (205)

Discharge ID

mm (in)

70 (2.75)

ID : Inner diameter.

*    Without flexible pipe and blower pipes.

**   With frexible pipe and blower pipes.

Summary of Contents for PB-655









Reviews: