background image

4

INTERNATIONAL

 

SYMBOLS

S

AFETY

 I

NSTRUCTIONS

PERSONAL

 

CONDITION

 

AND

 

SAFETY

 

EQUIPMENT

WARNING   

   DANGER

Edger users risk injury to themselves and others if the edger is used improperly and or safety precautions are not
followed. Proper clothing and safety gear must be worn when operating an edger.

HOT

SURFACE

Symbol

description/

application

Symbol form/

shape

Symbol

description/

application

Symbol form/

shape

Read and understand

Operator's Manual.

WEAR EYES, EARS

AND HEAD

PROTECTION

FUEL AND OIL

MIXTURE

Finger Severing

Safety/Alert

AVOID ALL POWER
LINES. THIS UNIT IS

NOT INSULATED

AGAINST

ELECTRICAL

CURRENT.

WEAR HAND

PROTECTION. USE

TWO HANDED.

DO NOT SMOKE

NEAR FUEL.

DO NOT ALLOW

FLAMES OR

SPARKS NEAR

FUEL.

Keep bystanders away

15 m (50 ft.)

Symbol

description/

application

Symbol form/

shape

Symbol

description/

application

Symbol form/

shape

Carburetor
adjustment
- Idle speed

Carburetor

adjustment

- High speed

mixture

Emergency stop

Carburetor

adjustment

- Low speed

mixture

Wear slip

resistant foot

wear.

Ignition

ON/OFF

Primer bulb

Keep feet away

from blade

Thrown

objects

Direction of

blade

CHOKE CONTROL

"COLD START"

POSITION

(CHOKE CLOSED)

CHOKE CONTROL

"RUN"

POSITION

(CHOKE OPEN)

Physical Condition

Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.

Eye Protection

Wear eye protection that meets ANSI Z87.1 or CE
requirements whenever you operate the unit.

Hand Protection

Wear no-slip, heavy duty work gloves to improve your
grip on the edger handles.  Gloves also reduce the
transmission of machine vibration to your hands.

Hearing Protection

ECHO recommends wearing hearing protection whenever
unit is used.

Proper Clothing

Wear snug fitting, durable clothing;
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
• DO NOT WEAR TIES, SCARVES, JEWELRY.

Wear sturdy work shoes with non-skid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.

Summary of Contents for PE-200

























Reviews: