Echo PE-266S Operator'S Manual Download | Manualshive

Page: 15 / 36

background image

PE-266/S

OPERATION

X7502026302

15

© 3/2013 ECHO Inc.

OPERATION

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects
away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts
have come to a complete stop before removing obstructions, clearing debris, or servicing unit.

Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark
arrestor to prevent discharge of hot particles from the engine. Metal blade use also can create
sparks if the blade strikes rocks, metal, or other hard objects. Contact local fire authorities for laws
or regulations regarding fire prevention requirements.

Fuel

Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO
requirements are NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels
may cause performance problems, loss of power, overheating, fuel vapor lock, and unintended
machine operation, including, but not limited to, improper clutch engagement. Alternative fuels may
also cause premature deterioration of fuel lines, gaskets, carburetors and other engine components.

Fuel Requirements

Gasoline

- Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may

contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing
methanol (wood alcohol) is

NOT

approved.

Two Stroke Oil

- A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FD Standards

must be used. Echo brand premium Power Blend X

TM

Universal 2-Stroke Oil meets these standards. Engine

problems due to inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and
J.A.S.O. FD certified oil, such as Echo premium Power Blend X

TM

, will void the two-stroke engine warranty.

Echo premium Power Blend X

TM

Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo

engines sold in the past regardless of ratio specified in those manuals.

Handling Fuel

Fuel is VERY flammable. Use extreme care when mixing, storing or handling, or serious personal
injury may result.

•

Use an approved fuel container.

•

DO NOT smoke near fuel.

•

DO NOT allow flames or sparks near fuel.

«
...
13
14
15
16
17
...
»

Summary of Contents for PE-266S





































Reviews:

No comments

Related manuals for PE-266S

Brand: Nidek Medical Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands