background image

32

X7502026302

© 3/2013 ECHO Inc.

WARRANTY STATEMENTS

PE-266/S

 

 

PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES

&GJ*  *  
&^J*          

ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS

This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior 
performance.  To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD 
13738 and JASO M345FD Standards.

  !"#$%!&()* 

  *  @$*

L-EGD (ISO/CD 13738) and JASO M345FD Standards.  The use of two-stroke oils designed for other applications, such as for outboard motors 
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty. 

THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:

&

:    * that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD 
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered 
oil, will void the two-stroke engine limited warranty.  !"#$ > ={ 9* $  meets the ISO-L-EGD and JASO M345FD  
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per 
the statement listed in the EPA or California Emission Defect Warranty Explanation. 

&

X  []   |G.  Only use gasoline which 
contains |G . Gasohol which contains a 

+6+7+

\J}[ ]\~}/9=![ ]

is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.

&

!  +

&

X        
engine speeds as listed in your operator’s manual.

&

$        

&

X      

&

X         
of unauthorized attachments. 

&

@    €     
manual.  Preventative maintenance as outlined in the operators manual is the customer’s responsibility.

&

'  **     %!"#$   
warranty period.

&

" parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups. 

&

B              €    $!/        $
Manuals.

&

$      
screen.

&

<ƒ[^J] ƒƒ

&

X       
with recommended grease or oil change intervals.

&

X #!X?„<"

®

 

 beyond recommended capacity. 

&

X    +  

&

<      
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.

It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting 
WWW.ECHO-USA.COMZ       %
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long 
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or 
€    9     !"#$
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.

DISCLAIMER OF IMPLIED WARRANTIES

9           '@9?!'$<><9@"B:<>B>$!
OR USE and any implied warranty of 

MERCHANTABILITY

   !"#$   

    €   9   
9    !"#$

99922201032

11/18/2011

Summary of Contents for PE-266S





































Reviews:

Related manuals for PE-266S