Echo SC-2013 Operator'S Manual Download | Manualshive

Page: 26 / 34

background image

21

3 INCH CHIPPER/SHREDDER

Section

6 TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSES

REMEDY

Engine will not start

Lack of fuel or oil

Fill fuel tank and check oil level

Spark plug disconnected

Connect spark plug

Kill switch on access cover is damaged

Test kill switch. Replace if it is not working

Dirty, stale, or contaminated fuel

Drain and refill fuel tank with fresh, clean
unleaded regular gasoline or diesel.
Replace fuel filter.

Internal engine problems

See your engine dealer

Engine or rotor stalls or
stops

Chipper rotor housing or discharge tube is
plugged

Shut off engine and disengage belt
engagement. Refer to manual for
information on clearing a plugged rotor.
Never use the belt engagement to clear a
plugged rotor.

Feeding material that is too large

Limit branch size to rated capacity

Engine overheats

Cooling system plugged

Clean cooling fan and cooling fins on the
radiator or engine block

Improper coolant level

Fill engine to correct coolant level. Refer to
the engine owner’s manual

Engine stalls or
belt squeals when
engaging belt

Engaging belt too fast

Reduce engagement speed

Belt tension too loose

$GMXVWWHQVLRQHU5HSODFHEHOWLIQHHGHG

Engine runs, but dies
or does not accelerate
properly

Air filter dirty

Clean or replace

Fuel filter dirty

Replace

Fuel vent plugged

Clean or replace

Spark plug dirty/worn

&OHDQDQGDGMXVWRUUHSODFH

Carburetor vibration

$GMXVW

Cooling system dirty/plugged

Clean

Spark arrestor* plugged

Clean or replace

Machine chips poorly

Dull chipper blades

Flip, sharpen, or replace

Drive belts loose or worn

,QVSHFWGULYHEHOWVDGMXVWRUUHSODFHLI

needed

Feeding material that is too large

Limit branch size to rated capacity

Before performing any of the corrections in this troubleshooting chart, refer to the appropriate information contained in
this manual for the correct safety precautions and operating or maintenance procedures. Contact your dealer or ECHO
for service problems with the machine.

*If equipped

ENGLISH

«
...
24
25
26
27
28
...
»

Summary of Contents for SC-2013



































Reviews:

No comments

Related manuals for SC-2013

Brand: Gladwork Pages: 6

Brand: HSM Pages: 6

Brand: Cub Cadet Pages: 60

Brand: Rexel Pages: 31

Brand: Fellowes Pages: 4

Brand: Fellowes Pages: 4

Brand: Fellowes Pages: 4

Brand: Fellowes Pages: 4

Brand: Fellowes Pages: 4

Brand: Fellowes Pages: 4

Brand: Hama Pages: 62

POWERSHRED 465Ms

Brand: Fellowes Pages: 8

Powershred 1800C

Brand: Fellowes Pages: 8

Powershred 12C15

Brand: Fellowes Pages: 4

Brand: Lenoxx Pages: 2

Brand: Intimus Pages: 20

Brand: Cocraft Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands