Echo SRM-260 - 12-06 Operator'S Manual Download

Page: 27 / 28

RASS

RIMMER

RUSH

UTTER

PERATOR

ANUAL

PECIFICATIONS

MODEL ----------------------------------------------------- SRM-260, SRM-260S

Length w/o cutter head ----------------------------------- 1795 mm (70.7 in.)

Width -------------------------------------------------------- 250 mm (9.84 in.)

Height ------------------------------------------------------- 250 mm (9.84 in.)

Weight (dry) w/Cutter Head (SRM-260) ---------------- 5.23 kg (11.5 lb.)

Weight (dry) w/Cutter Head (SRM-260S) -------------- 5.03 kg (11.1 lb.)

Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine

Bore ---------------------------------------------------------- 34.0 mm (1.34 in.)

Stroke -------------------------------------------------------- 28.0 mm (1.10 in.)

Displacement ----------------------------------------------- 25.4 cc (1.55 cu. in.)

Exhaust ------------------------------------------------------ Spark Arrestor Muffler w/catalyst

Carburetor -------------------------------------------------- Walbro diaphragm model w/purge pump

Ignition System -------------------------------------------- Flywheel magneto, capacitor discharge

Spark Plug -------------------------------------------------- NGK BPM-8Y (Gap 0.65 mm (0.026 in.)

Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil)

Fuel/Oil Ratio ----------------------------------------------- 50:1 two-stroke air cooled engine oil

Gasoline ----------------------------------------------------- 89 Octane unleaded. DO NOT use fuel containing methyl alcohol,

more than 10% ethyl alcohol or 15% MTBE.

Oil ------------------------------------------------------------ Power Blend

Premium Universal 2-Stroke Oil

Fuel Tank Capacity ---------------------------------------- 0.58 lit. (19.6 US fl. oz.)

Starter System ---------------------------------------------- Automatic Rewind Starter

Clutch ------------------------------------------------------- Centrifugal Type

Vibration Isolated System --------------------------------- Rubber cushion on engine mount (heavy duty). Rubber grip on

front handle

Operating Rod ---------------------------------------------- 25.0 mm aluminum Tube

Drive Shaft (SRM-260) ------------------------------------ 6.35 mm (1/4 in.) flexible shaft

Drive Shaft (SRM-260S) ----------------------------------- 7.0 mm spline steel shaft

Gear Case Ratio -------------------------------------------- 1.4:1 Reduction

Rotating Direction ----------------------------------------- Counter Clockwise; viewed from top

Cutter Head ------------------------------------------------- Nylon line head (2-line) with .095 Crossfire™ Line capacity 6m (20 ft.)

Handle* ----------------------------------------------------- Front - Loop and Right Rear Handle w/rubber grips

Shoulder Harness ------------------------------------------ Optional

Idle Speed --------------------------------------------------- 2,750- 3,250 RPM

Clutch Engagement Speed -------------------------------- 3,500 - 4,100 RPM

Wide Open Throttle Speed (W.O.T.)

with Nylon Line Head ------------------------------------- 8500 - 9500 RPM

Wide Open Throttle Speed (W.O.T.) with Blade ------ 9500 - 11,000 RPM

Summary of Contents for SRM-260 - 12-06





























Search results

Summary of Contents for SRM-260 - 12-06

Reviews:

Related manuals for SRM-260 - 12-06

Brands by name

Popular brands

Echo SRM-260 - 12-06, Operator'S Manual

Search results

Summary of Contents for SRM-260 - 12-06

Reviews:

Related manuals for SRM-260 - 12-06

Brands by name

Popular brands