background image

3

SAFETY INSTRUCTIONS

  1. Do Not operate the unit when you are

fatigued.

  2. Do Not operate if other people or animals

are in the work area.

  3. Do Not operate the unit without the shield

correctly in position.

  4. Do Not operate in a confined area. Carbon

monoxide exhaust gas is highly poisonous.

  5. Do Not operate the unit while you are

smoking.

  6. Always wear eye protection goggles when

operating the unit.

  7. Always hold the unit firmly with both hands

and with fingers and thumbs encircling the
handles.

  8. Always obey local ordinances regulating the

use of internal combustion engines in your
area.

  9. Always use the cutting attachments as

approved and supplied by ECHO Inc. for
your unit.

10. Always remain alert when operating the unit

to avoid possible injury to yourself and other
people.

11. Always wear the shoulder harness when

operating the unit.

12. Do not operate the unit while under the

influences of drugs or alcohol.

WARNING   

   DANGER

1. Do Not smoke while handling gasoline.

2. Do Not refuel a hot engine. Wait unit it cools.

3. Do Not overfill the tank. Spiled fuel must be

wiped up.

4. Always stop the engine when refueling.

5. Always remove the fuel cap slowly in order to

relieve any pressure build up in the tank.

6. Always restart the engine at least 3 m

(10 feet) away from the refueling posint.

7. Always store gasoline in an approved

container.

RULES FOR SAFE OPERATION

ATTENTION

For your protection when operating this unit,
comly with all Safety Rules as listed in the
Operator’s Manual. (Replacement manuals are
available from your ECHO dealer.)

  1. Do not operate unless the debris shield and

safety harness are in good condition and
properly installed.

  2. Do not operate if other persons or animals

are in the work area.

  3. Do not operate without eye protection

goggles available from your ECHO dealer.

WARNING   

   DANGER

SERIOUS INJURY MAY RESULT FROM THE
IMPROPER USE OF STEEL BLADES.
COMPLY WITH ALL SAFETY INSTRUCTIONS
LISTED IN THE OPERATOR’S MANUAL AND
SUPPLIED WITH THE BLADES.

1. THE ECHO SAW TOOTH BLADE IS

DESIGNED TO CUT BRUSH AND SMALL
TREES.

2. THE ECHO 8 TOOTH ROTARY KNIFE

BLADE IS DESIGNED TO CUT HEAVY
WEEDS AND GRASS. TO AVOID INJURY
DUE TO KICK BACK OR BLADE
FRACTURE, DO NOT USE THIS BLADE TO
CUT BRUSH OR TREES.

3. ECHO INC. WILL NOT BE RESPONSIBLE

FOR THE FAILURE OF CUTTING DEVICES
WHICH HAVE NOT BEEN TESTED AND
APPROVED BY ECHO FOR USE WITH
THIS UNIT.

Summary of Contents for SRM-400





















Reviews: