background image

wheeled trimmer

9

ENGLISH

  

 

 

 

Section

5

SERvIcE & 

maINTENaNcE

The standard cutting height is 2-3/4 inches. The cutting 

height can be adjusted down approximately 3/4 inch by 

turning the trimmer head disk over.  To adjust the cutting 

height:

Insert a 9/16” open end wrench into the trimmer frame 

1. 

(Figure 5.1).
Rotate  the  trimmer  head  until  the  wrench  engages 

2. 

with the trimmer shaft.
While  holding  the  wrench,  twist  the  trimmer  head 

3. 

weldment counterclockwise to remove.  use a channel 

lock or pipe wrench if necessary.
Turn trimmer head disk over and replace on trimmer 

4. 

spindle.
Return  trimmer  head  weldment  and  turn  clockwise 

5. 

to tighten.

Figure 5.1 - Cutting Height Adjustment

9/16”  WRENCH

TRIMMER 

DISC

TRIMMER 

HEAD

5.1  maINTENaNcE ScHEduLE

5.2  cuTTING HEIGHT adjuSTmENT

The items listed in this service and maintenance schedule are to be checked, and if necessary, corrective action taken. 

This schedule is designed for units operating under normal conditions. If the unit is operating in adverse or severe 

conditions, it may be necessary for the items to be checked and serviced more frequently.

SEE  ENGINE  oWNER’S  maNuaL  FoR  FuRTHER  ENGINE  maINTENaNcE  aNd  TRoubLESHooTING 

INFoRmaTIoN.

FreQuenCY

compoNENT

maINTENaNcE  

REQuIREd

REFER To 

ENGINE 

opERaToR’S 

maNuaL

bEFoRE 

EacH uSE

EvERY 8 

HouRS

EvERY 

YEaR

AIR CLEANER

ChECK AND CLEAN (1)

 

ENgINE OIL

ChANgE (1) (3)

 

SPARK PLug

ChECK CONDITION AND gAP

 

ENgINE OIL

ChECK/FILL (1) (3)

 

FuEL TANK

ChECK/FILL

ALL INTERNAL AND ExTERNAL 

NuTS AND BOLTS

ChECK TIghTNESS

 

BATTERy CONNECTIONS

ChECK

ENTIRE MAChINE

CLEAN

COOLINg ShROuDS

CLEAN (1) (2)

STARTER DRIvE

SERvICE (2)

(1) Perform more frequently in dusty, dirty or severe usage conditions.
(2) have a Briggs or honda engine service dealer perform this service.
(3) Change oil after first 5 to 8 hrs of use, then every 50 hours or every season.

as the Limited Warranty states, failure by the owner to perform normal maintenance will void the machine’s 

warranty.

Summary of Contents for WT160S

































Reviews: