Milestone AV Technologies and its affi
liated
corporations and subsidiaries (collectively,
“Milestone”), intend to make this manual accurate
and complete. However, Milestone makes no
claim that the information contained herein
covers all details, conditions, or variations. Nor
does it provide for every possible contingency
in connection with the installation or use of
this product. The information contained in this
document is subject to change without notice
or obligation of any kind. Milestone makes no
representation of warranty, expressed or implied,
regarding the information contained herein.
Milestone assumes no responsibility for accuracy,
completeness or suffi
ciency of the information
contained in this document.
©2017 Milestone AV Technologies. All rights
reserved. ECHOGEAR is a Milestone brand.
ECHOGEAR and the ECHOGEAR logo are
trademarks of Milestone.
Made in China.
Milestone Global Headquarters
• 6436 City West Parkway • Eden Prairie, MN 55344 USA
6901-002430 05
Adjustments
5-1
4-1
4-2
5-2
5-3
5-4
TO ADJUST TV LEVEL
,
loosen screws [S] on
the rear of the arm
plate, adjust level, and
retighten to secure.
TO ADJUST THE TILT
, fi rst rotate (loosen or tighten) the tilt lever
as far as you can, then:
a
Pull and hold the lever outward,
b
Rotate the lever in the opposite direction,
c
Release the lever back into position,
d
Rotate the lever to tighten or loosen.
Repeat as needed.
LOOSEN: to adjust the TV tilt position.
TIGHTEN: to set the TV in place at your desired tilt angle.
a
b
d
c
[S]
07
Loosen
Tighten
Drill two pilot holes using a 7/32 in. (5.5 mm)
diameter drill bit.
IMPORTANT
:
Pilot holes must be drilled to a depth
of 3 in. (75 mm).
Be sure to drill into the center of the stud.
01
01
01
Locate your stud. Verify and mark the center of
the stud by fi nding the stud edges using an awl,
a thin nail, or an edge-to-edge stud fi nder.
Position the wall plate
01
at your desired height
and line up the holes with your stud center line.
Level the wall plate and mark the holes.
IMPORTANT
:
Be sure to only use the top hole
and bottom slot for mounting.
Hang TV onto arm
and using hex key
07
, secure with
screws
[S]
saved
from
Step 1
.
IMPORTANT
:
These screws
[S]
must
be installed to
secure the TV onto
the arm
01
.
07
[S]
05
06
05
06
STEP 6
STEP 5
Wall Plate Install (Wood Stud)
(a) Flat Back
configuration
B
illustrated
configuration
B
illustrated
(b) Round Back / Extra Space
CAUTION:
Avoid potential personal injuries
and property damage!
●
Drywall covering the wall must not exceed
5/8 in. (16 mm)
●
Minimum wood stud size: common 2 x 4 in.
(51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
CAUTION:
Avoid potential personal injury
or property damage! All lag bolts
05
MUST BE
firmly tightened to prevent unwanted movement
of the wall plate
01
.
CAUTION:
Ensure the wall plate is
securely fastened to the wall before continuing
on to the next step.
M4 M6 M8
3 in. (75 mm)
7/32 in.
(5.5 mm)
Position your TV bracket
configuration
A
or
B
over your
TV hole pattern - making sure
the bracket is centered and level
over the TV hole pattern.
Secure the bracket using your
screw/washer/spacer selection:
(
a
) for
Flat Back
(
b
) for
Round Back / Extra Space
CAUTION:
Ensure TV
bracket is securely fastened
before moving on to the next step.
10
14
16
16
18 19
11
15
17
17
09
13
08
12
STEP 4
Install TV bracket
Install wall plate
01
using lag bolts
05
and
washers
06
. Tighten the lag bolts
05
only until
they are pulled firmly against the wall plate
01
.
Note Orientation
FLAT BACK
ROUND
BACK
CABLES
INSET
HOLES
a
b
Too Short
Too Long
Correct
If your TV has a flat back, AND you want your TV
closer to the wall, use the shorter screws (
a
).
Use spacers and long screws (
b
) to accommodate:
• Round/irregular back TVs
• TVs with inset mounting holes
• Extra space needed for cables
CAUTION:
Verify
adequate thread engagement
with the screw/washer/spacer
combination AND TV bracket.
-
Too short will not hold the TV.
-
Too long will damage the TV.
Determine which
screw diameter (
M4,
M6, or M8
) to use.
Alternate
Setups
