FlacheSAN1L-D 1U 20-Bay Storage Server Quick Guide
5.
Install CPU and memory
(may be sold separately)
to their respective slots on the motherboard. Please be aware
of each component’s installation requirements and
prerequisites. Refer to the motherboard’s TPS for details.
CPU 2
CPU 1
EP2C602-2T/D16
- Support for Intel Xeon E5-1600/
2600/4600 and V2 series
processors
- E5-1600 supports single socket
- Dual Socket R (LGA2011)
- DDR3 RDIMM
- 512 GB max capacity in 16x 240-
pin DIMM slots
- Quad Channel DDR3 1600/1333/
1066 LR/Registered/ECC/UDIMM
- PCIe Gen3 x16 slots
- PCIE6 is routed to CPU1
- PCIE7 is available only when
CPU2 is installed
6.
Install OS disk(s)
(may be sold separately) into the
bracket. Applies only to non-expander configuration.
1. Remove the bracket
from the enclosure
2. Install one or two
disk(s) to the bracket,
secure it with 4 M3
screws each at blue
circle locations
3. Place the OS disk
bracket assembly back
to the enclosure.
Secure with provided
screws (red circles)
4. Connect SATA
cables and power
cables to the disk(s)
7.
Install IO cards
(may be sold separately) to PCI-e slots.
1. Unscrew 3 screws (red circles) to remove
the riser card / IO card bracket
2. Slide IO card(s) to the
PCIe slot(s). Note their
bracket profiles. Secure at
blue circle(s)
3. Return the riser card assembly to
enclosure. Secure with screws
For more IO card information, refer to the user’s guide for the
IO card.
8.
Put the top cover.
Once we are finished with the
internals of the system, close the top of the chassis as
described below:
2. Slide the cover
forward
3. Secure the cover
with eight 6-32
thread screws
1. Place the top cover to the
chassis using the pin as a guidance
9.
Remove drive trays
from the enclosure.
1. Push the tray
latch to release
the tray handle
2. Pull the tray
handle to remove
the drive tray out
from the
enclosure bay
10.
Install drives into trays.
Follow the diagram
closely. SSD and HDD sold separately. For HDD installation, the
use of M3 screws is recommended.
1. Slide the drive in with the
IO connector side head first
to the back of the tray
4. Snap in the
hinge back to
lock position
3. Snug the
other end of
the drive into
the tray
2. Make
sure that
the drive
goes
underneath
the hooks
To remove the disk, do the steps in reverse.
Poke from the bottom hole to help release the disk.
11.
Place the unit to the rack.
Please refer to Rail Kit
Installation Guide on how to mount the
enclosure.
Caution:
At least two people are required to
lift a fully populated chassis
12.
Install the populated drive trays
into the
enclosure with the drives properly secured to the hard drive
trays.
1. Push the tray by the
latch all the way into the
drive bay to ensure a
complete insertion
2. Secure the drive tray to
the enclosure by placing the
tray handle to lock position
13.
Drive mapping
incrementally goes from left to
bottom going and to the right, depending on the cable
connection of the expander / on-board SATA ports.
1
20
4
5
14.
Plug in the power cords
to the AC receptacles on
the back of the unit and secure it with the wire lock.
15.
Press the power button
on the front of the unit
after connecting a monitor and input devices, and get ready for
software setup.
If you have any technical questions, please contact your authorized dealer before contacting us.
For more information please visit our website at
www.echostreams.com
