background image

 

 

8.

 

Do not install near any heat sources such as radiators, heat registers, stoves, or 

other apparatus (including amplifiers) that produce heat.  

9.

 

Do  not  defeat  the  safety  purpose  of  the  polarized  or  grounding  type  plug.  A 
polarized plug has two blades with one wider than the other. A grounding type 

plug has two blades and a third grounding prong. The wide blade and the third 

prong  are  provided  for  your  safety.  If  the  provided  plug  does  not  fit  into  your 

outlet, consult an electrician for replacement of the obsolete outlet. 

10.

 

Protect  the  power  cord  from  being  walked  on  or  pinched  particularly  at  the 

plugs,  convenience  receptacles,  and  at  the  point  where  they  exit  from  the 

apparatus.  

11.

 

Only use attachments/accessories specified by the manufacturer. 

12.

 

Unplug the apparatus during lightening sorts or when unused for long periods of 

time. 

13.

 

Refer  all  servicing  to  qualified  personnel.  Servicing  is  required  when  the 

apparatus has been damaged in any way, such as power supply cord or plug is 

damaged, liquid has been spilled or objects have fallen into the apparatus, the 

apparatus has been exposed to rain or moisture, does not operate normally, or 

has been dropped. 

14.

 

Disconnecting  from  mains:  switching  off  the  POWER  switch  all  the  functions 

and light indicators of the amplifier will be stopped, but fully disconnecting the 

device  from  mains  is  done  unplugging  the  power  cord  from  the  mains  input 

socket. For this reason, it always shall remain readily operable. 

15.

 

Equipment is connected to a socket-outlet with earthing connection by means of 

a power cord.  

16.

 

The marking information is located at the bottom of the apparatus. 

17.

 

The apparatus shall not be exposed to dripping or splashing and that no objects 

filled with liquids, such as vases, shall be placed on apparatus.  

 

WARNING

:

 

This  product  must  not be  discarded,  under  any  circumstance,  as 

unsorted  urban  waste.  Take  it  to  the  nearest  electrical  and  electronic  waste 
treatment centre. 

 

NEEC  AUDIO  BARCELONA,  S.L.

  accepts  no  liability  for  any  damage  that  may  be 

caused to people, animal or objects due to failure to comply with the warnings above.  

 

 

Summary of Contents for MIMO4040DN





















Reviews: