background image

Preface 

The unit is a new presentation laser scanner which allows hands free  bar code 

scanning. Bar code labels are read by presenting the labels towards the unit. 

Scanning labels with this unit  hardly requires any arm movement.  

As a result only little free space on the counter top is necessary. 
This unit can either be fixed on a counter surface or on a flexible stand.  The 

flexible stand allows you to direct the scan pattern in a way that is optimal for 

your application. 
This unit reads all popular bar code symbologies. An important feature of this 

unit is its programmable sleep mode. If the unit is not used within a 

programmable period of time, the unit switches off automatically. The unit can 

be re-activated by pressing the switch on top of the unit. 

This unit is available in two colour versions, both supporting multiple interface 

for communication with any host system. The multiple interface versions are:  

RS-232 + USB + P-USB + Keyboard Wedge. 
This manual contains two chapters and three appendices. The first chapter 

describes this unit and its general features. The description for installation can 

be found in the second chapter. Precisely follow the instructions for the 

installation of the unit. Default settings can be changed with the bar code 

labels from the Configuration Guide that came with the unit. Appendix A gives 

the pin definition for the Data ports of the unit. The pin definition may be 

required when you want to make a new cable for communication with the POS/

computer. Technical specifications of this unit can be found in Appendix B. 

Refer to Appendix C for troubleshooting if 

the unit

 is not working properly. 

Summary of Contents for EC-OS-7200D





































Reviews: