background image

13

Eclipse Packaged Gas BoostPak, V2,  Installation Guide 630-2, 6/22/2010

Maintenance &
Troubleshooting

Monthly Checklist

•  Inspect and tighten loose mechanical components

•  Look for signs of damage and repair

•  Test operation if the unit has not run and check for 

excessive vibration

•  Clean the booster motor housing

•  Clean the heat exchanger, its motor, and cooling fan 

(MH only)

•  Wipe clean the control panel surfaces

Yearly Checklist

•  Check inlet and outlet pressure switch settings

•  Check and compare inlet and outlet pressures to the 

initial commissioning record sheet

•  Measure and compare the power supply and motor 

current to the record sheet

• Perform operational test in the commissioning 

section of this guide

Alarm Conditions

Certain conditions will cause the ALARM to come on. To
silence the alarm, press the ALARM SILENCE push
button.

•  INLET LOW GAS MANUAL RESET PRESSURE 

SWITCH opens due to low utility line pressure. The 
LOW GAS light comes on and the booster motor will 
stop running. When the pressure is restored, this 
switch must be manually pushed to reset its contact.

• DISCHARGE GAS PRESSURE SWITCH fails to 

make contact within 15 seconds. The LOW GAS 
light comes on; the booster will not shut down.

•  If the motor wiring or internal temperature switch 

opens, then the motor will stop causing the 
discharge gas pressure switch to open. Then the 
ALARM and LOW GAS light come on.

•  A booster motor overload condition will shut down 

the booster and the MOTOR FAULT light and 
ALARM will come on.

•  A heat exchanger motor overload condition will shut 

down the heat exchanger fan and the MOTOR 
FAULT light and ALARM will come on (MH only).

Problem

Possible Cause

Solution

No POWER ON light

Main supply power is off

Be sure main power to the system is 
switched “on”.

Main disconnect switch is off

Turn the control panel main disconnect 
switch on.

Loose connection

Check for voltage on panel terminals, 
turn off main power and inspect, 
tighten wire connection.

Blown fuse

Verify that all fuses are good and 
properly installed. If blown, have a 
qualified electrician determine the 
cause and fix before replacing fuse.

Cannot initiate start sequence

Inlet low gas manual reset pressure 
switch has activated

Check incoming gas pressure: adjust if 
necessary.

Check pressure switch setting and 
operation.

If used, check that the pressure switch 
isolating valve is not closed.

6

Summary of Contents for BoostPak























Reviews: