background image

   

 

 

Eco Pacific/Super Star- Installation and Service Instructions 20173                 

Description 

The 

‘Super Star’ series is designed as a single stage non-condensing central gas ducted heating 

unit.    Throughout  these  installation-instructions  references  is  made  to  the  general  aspect  of  the 
units with dimensions shown through Figures 1&2 and Table 2.  

 

Figure 1 and 2: 

General aspects, please refer Table 2 for dimensions. 

As  shown  in  figure  1&2  the  access  service  panel,  where  the  gas  power  and  thermostat  are 
connected, is the front of the unit.  With respect to the front access the rear side contains the fan 
box where the motor and the wheel are fitted for return air inlet. The burner heat exchanger box 
with  service  access  panel  is  the  front  section  of  the  heater  where  the  supply  air  is  taken  from, 
while the flue is discharged through the side panels of the front section. The front section behind 
the  service  panel  contains  access  to  the  Printed  Circuit  Board  (PCB)  controls,  the  gas  burner, 
combustion  fan,  and  the  gas  valve. The  gas  inlet  connection  is  given  at  the  front lower  section. 
Access to the fan wheel and motor is achieved on the far-right hand side. 

Models 

These installation instructions cover the Eco Pacific ‘

Super  Star’

  range  of  internal  and  external 

heaters  of  12.5,  16.5,  19.5,  26.5-  and  31.5-kw  heat  output  class.    The  SS  and  HB  range  of 
heaters is intended for use with natural gas as specified on the data plate. 

Specifications 

The technical information and overall dimensions of each model are given in Table 1 and Table 2 
respectively.  The appliance data plate found on the front panel of each heater unit complements 
this information. 

Table 1:  Specifications data 

 

                          Models SS series

 

Models HB series 

         Specification

 

SS512 

SS516 

SS520 

SS525  

SS530 

HB416 

HB420 

 

Heat Input (MJ/h) 

48 

64 

80 

102 

120 

64 

80 

 

Heat Output (kW) 

12.5 

16.5 

19.5 

26.5 

31.5 

16.5 

20 

 

Air Flow (L/s at 75 Pa ESP)  460 

470 

630 

770 

940 

470 

650 

 

Weight (kg) 

46 

51 

58 

68 

70 

48 

53 

 

Electrical Power(V/Ph/Hz) 

240/1/5

240/1/5

240/1/
50 

240/1/5

240/1/5

240/1/5

240/1/5

 

Thermostat Control (V) 

24 

24 

24 

24 

24 

24 

24 

 

Total Current (A) 

2.5 

2.5 

3.5 

5.5 

2.5 

3.5 

 

Maximum  Add-On  Cooling 
recommended, kW 

12 

16 

18-20 

9.5 

12 

 

Energy Star Rating 

4.5 

4.7 

4.5 

4.7 

4.8 

4.6 

4.7 

 

Summary of Contents for Super Star HB Series





















Reviews: