background image

 

 

This appliance is very heavy and every care should be taken when trying to manoeuvre 
it. 

Do not attempt to move or lift the appliance by the door handles, this could cause 

damage to the doors and handles. 

It must be sited on a solid, level floor constructed in 

accordance with any Building Regulations which may apply to the site.

 

 

 

 

It is important for the correct operation of this appliance that the installation space and 
clearances  around  the  appliance  are  in  line  with  the  specifications  detailed  in  these 
instructions. 
 

 

Sufficient  space  should  be  available  to  allow  the  doors  to  be  fully  opened  in  excess  of 
120

°

 from the closed position. 

 
 

 

Ventilation openings on the side rear and front of the appliance should never be blocked 
or restricted. see ventilation requirements 

 

 

 

This appliance is capable of being operational at all times. 

Parts of the appliance will 

become  very  hot,  and  remain  hot  for  long  periods.

  Only  adults  should  operate  this 

appliance and only in accordance with the user instructions. Care should be taken when 
using the cooker and the use of oven gloves is recommended when applicable. Children 
should be supervised at all times if in the vicinity of the cooker.  

 

 

In the interest of hygiene and safety the cooker should be kept clean at all times. 

 

 

The  cooker  is  designed  for  cooking  foods  only  and  must  not  be  used  for  any  other 
purpose. 

 

 

Always allow to cool before cleaning and carrying out maintenance work.  

 

 

Do not use unstable or unsuitable saucepans and position handles away from the edge of 
the hot plate. Thick, flat based saucepans are recommended for best results. 

 

 

Do not place combustible materials onto the hot plate surfaces even when the cooker is 
off.  

 

 

Your  Eco  Range  Cooker  should  be  serviced  at  least  once  every  twelve  months.

 

It  is 

impossible to service your cooker while it is hot, therefore DO NOT use your appliance 
12 hours before a service is required. 

 

Important:  

The installer is responsible to ensure that all persons involved in the installation be provided 
with  the  correct  health  and  safety  clothing  when  handling  materials  which  are  known  to 
cause potential harm. 

 

Ceramic materials: Facemask and gloves must be worn, Contact with eyes, skin and 
throat must also be avoided.  

 

Fuels:  Wear  gloves  –  avoid  ignition  sources  –  Waste  fuel  should  be  disposed  of 
correctly, not via domestic waste water courses. 

 

Fire cement: Wear gloves – wash hands.  

Summary of Contents for 15/21




































Reviews: